manualshive.com logo in svg

Hanna Instruments HI 98402, Instruction Manual, Page: 17 / 20

Share
Download
Hanna Instruments HI 98402 Instruction Manual Download Page 17

17

FLUORIDE ELECTRODE CLEANING

General:

Rinse the fluoride electrode with deionized water.

Protein, oil & fat:

Clean the electrode tip with a cotton wool

soaked in alcohol, then rinse with deionized water.

IMPORTANT

: After cleaning, rinse the fluoride electrode thoroughly

with deionized water and dry it attentively with a non-
abrasive cloth.

TROUBLESHOOTING

•

Reading fluctuates

: could be due to dirty or blocked reference

electrode junction. Follow the cleaning procedure above.

•

Reading drifts

: submerge the tip of the reference electrode in

HI 7082

 solution at a temperature of 50-60°C for about 1 hour.

Afterwards, rinse with deionized water.

•

No slope (meter always reads the same value)

: the bulb or

stem of the fluoride electrode might be cracked. Repeat the mea-
surement with a new fluoride electrode.

•

Response (of the fluoride electrode) is sluggish

: immerse the

fluoride electrode in 

HI 4010-10

 solution for 3 hours.

Summary of Contents for HI 98402





















Reviews:

No comments