Hanna Instruments HI 9811-5 Instruction Manual Download Page 3

3

All rights are reserved. Reproduction in whole or in part is prohibited without 

the written consent of the copyright owner.

Remove the instrument from the packing material and examine 
it carefully to make sure that no damage has occurred during ship-
ment. If noticeable damage is found, please contact your local  
Hanna Instruments Office.
Each meter is supplied with:

• 

HI1285-5

, pH/EC/TDS/°C combination probe with 8-pin DIN 

connector and 1 m (3.3’) cable

 

HI70007

, pH7.01 sachet, 1 pc.

 

HI70031

, 1413 

µ

S/cm sachet, 1 pc.

 

HI70032

, 1382 ppm (mg/L) sachet, 1 pc.

 

HI700661

 cleaning solution sachet, 2 pcs.

  Instruction manual

•  1 x 9V alkaline battery.

Note:

 Save all packing material until you are sure that the instrument 

functions correctly. Any defective item must be returned in the 
original packing together with the supplied accessories.

HI9811-5

 is the complete, versatile, with a large LCD and splash-

proof portable combination meter designed with the utmost precision 
and simplicity. The instrument provides measurements for pH, EC and 
TDS ranges, which are easily selectable through the keypad on the 
front panel. 
Conductivity measurements are automatically compensated for tem-
perature changes with a built-in temperature sensor. The temperature 
coefficient is fixed at 2%/°C.

HI9811-5

 is a pH/EC/TDS meter designed for simplicity of use in 

taking pH, µS/cm, mg/L and temperature measurements. Suited for 
hydroponics, greenhouses, farming and ground water applications.

PRELIMINARY EXAMINATION

GENERAL DESCRIPTION

Summary of Contents for HI 9811-5

















Reviews: