HANGCHA CPD10-A Operation And Maintenance Manual Download

Page: 63 / 82

Preventive maintenance schedule

〇

—

Check, revise, adjust ×

—

Replace

—

Daily

；

—

Weekly

；

—

Monthly

；

—

Trimonthly

；

—

Semiannually

Battery

Item

Service required

Tools

(8 h)

(40 h)

(166 h)

(500 h)

(1000 h)

Ba
tt

Electrolyte level

Eyeballing

〇

Electrolyte proportion

Densimeter

〇

Battery quantity

〇

Terminal looseness

〇

Looseness of connecting
wire

〇

Cleanness of the battery
surface

〇

If there are tools on the
battery.

〇

The

tightness

and

smoothness of air cap

〇

Far away from firing

〇

Controller

Item

Service required

Tools

(8 h)

(40 h)

(166 h)

(500 h)

(1000 h)

Con

tro
lle

Check connector for worn

〇

Check

contactor

for

running

〇

Check micromove switch
for running

〇

Check

the

connection

among motor, battery and
power unit.

〇

Check the controller error
diagnose system

First time 2

years

Summary of Contents for CPD10-A



















































































Search results

Summary of Contents for CPD10-A

Reviews:

Related manuals for CPD10-A

Brands by name

Popular brands

HANGCHA CPD10-A, Operation And Maintenance Manual

Search results

Summary of Contents for CPD10-A

Reviews:

Related manuals for CPD10-A

Brands by name

Popular brands