Hangar 9 F-22 Raptor ARF Page 3 Assembly Manual Download

Page: 3 / 56

Contents of Kit

Introduction

Sophisticated sensors, unmatched close-in dogfighting skills and undetectable at long range. The F-22 Raptor

™

, the

U.S. Air Force's newest aircraft, is the most advanced stealth fighter in aviation technology. With the F-22 Raptor ARF,

beginners can learn to fly on a trainer that looks exciting. This revolutionary trainer sports red plastic NACA droops and

wing tip extensions that attach to the outer edge of the wing to provide extra stability. Once you’ve mastered the basics,

remove the droops and change the settings on the flap system to move up to the next level and enjoy sport aerobatics.

Progress from learning to fly to performing simple aerobatics with Hangar 9’s F-22 Raptor ARF.
The F-22 Raptor ARF is part of Hangar 9’s complete line of top-quality aircraft and accessories. Our Ready-To-Fly (RTF),

Almost-Ready-to-Fly (ARF), Progressive Trainer System (PTS

™

) and Plug-N-Play

(PNP

) trainer, performance and

scale airplanes are engineered and crafted to exacting standards and feature the finest components and materials, such as

our exclusive UltraCote

covering. Just as important, with every Hangar 9

product, you’ll get the service and technical

support you need to succeed.

E. HAN3831

Canopy Red/White

F. HAN3832

Landing Gear Set Complete

G. HAN3837

Cowling Red/White (uncut)

H. HAN3833

Spinner, 3-Blade

I. HAN3836

Spinner, 2-Blade

J. HAN3838

Wing Tube Set

K. HAN3839

NACA droops Red/White

Replacement Parts

A. HAN3826

Wing Set Red/White

B. HAN3827

Fuselage Red/White

C. HAN3828

Stabilizer Set w/Elevator

Red/White (2)

D. HAN3829

Fin Set w/Rudders Red/White (2)

Summary of Contents for F-22 Raptor ARF

























































Search results

Summary of Contents for F-22 Raptor ARF

Reviews:

Related manuals for F-22 Raptor ARF

Brands by name

Popular brands

Hangar 9 F-22 Raptor ARF, Assembly Manual

Search results

Summary of Contents for F-22 Raptor ARF

Reviews:

Related manuals for F-22 Raptor ARF

Brands by name

Popular brands