background image

3

5

8

2

11

1

15

17

6

7

4

Hangar 9 3.1m Sukhoi SU-26MM ARF Assembly Manual

Replacement Parts

1.  HAN106001  Fuselage w/ Hatch, 3.1m Sukhoi MM ARF
2.  HAN106002  Hatch w/ Canopy, 3.1m Sukhoi MM ARF
3.  HAN106003  Left Wing Panel, 3.1m Sukhoi MM ARF
4.  HAN106004  Right Wing Panel, 3.1m Sukhoi MM ARF
5.  HAN106005  Cowl (2 piece), 3.1m Sukhou MM ARF
6.  HAN106006  Left Stab Panel, 3,1m Sukhoi MM ARF
7.  HAN106007  Right Stab Panel, 3.1m SukhoiMM ARF
8.  HAN106008  Rudder, 3.1m Sukhoi MM ARF
9.  HAN106009  Carbon Wing Tube, 3.1m Sukhoi MM ARF 
10. HAN106010  Carbon Stab Tube, 3.1m Sukhoi MM ARF
11. HAN106011  Landing Gear, 3.1m Sukhoi MM ARF
12. HAN106012  Linkage Hdwr Set, 3.1m Sukhoi MM ARF

Replacement Parts

13.  HAN106013  Wheel Pant Set, 3.1m Sukhoi MM ARF
14.  HAN106014  Painted Pilot, 3.1m Sukhoi MM ARF
15.  HAN106015  Main Wheel Set, 3.1m Sukhoi MM ARF
16.  HAN106016  Main Axle Set, 3.1m Sukhoi MM ARF
17.  HAN106017  Tail Wheel Assy, 3.1m Sukhoi MM ARF
18.  HAN106018  55oz Gas Tank, 3.1m Sukhoi MM ARF
19.  HAN106019  Exhaust/Batt Mnt, 3.1m Sukhoi MM ARF
20.  HAN106020  Cowl/Cnpy screws, 3.1m Sukhoi MM ARF
21.  HAN106021  Decal Set
22.  HAN106022  Wing Bolts (6), 3.1m SukhoiMM ARF
23.  HAN106023  Fiberglass Control Horn Set

Contents of kit and Parts Number

 

Safety Precautions and Warnings

Read and follow all instructions and safety precautions 

before use. Improper use can result in fire, serious injury 

and damage to property.

COMPONENTS

Use only with compatible components. Should any 

compatibility questions exist please refer to the product 

instructions, the component instructions or contact Horizon 

Hobby, Inc.

FLIGHT

Fly only in open areas to ensure safety. It is recommended 

flying be done at AMA (Academy of Model Aeronautics) 

approved flying sites.

PROPELLER

Keep loose items that can get entangled in the propeller 

away from the prop, including loose clothing, neck strap or 

other objects such as pencils and screwdrivers. Especially 

keep your hands away from the propeller as sever injury can 

occur. Using a thick glove is highly recommended.

bATTERIES

 Notes on Lithium Polymer Batteries

  When misused Lithium Polymer batteries are significantly 

more volatile than alkaline or Ni-Cd/Ni-MH batteries used 

in RC applications. Always follow the manufacturer’s 

instructions when using and disposing of any batteries. 

Mishandling of Li-Po batteries can result in fire and rupture 

causing serious injury and damage.

SMALL PARTS

This kit includes small parts and should not be left 

unattended near children as choking and serious injury could 

result.

Age Recommendation: 

For advanced fliers ages 14 and above. This is not a toy.

4

Summary of Contents for 85cc Sukhoi SU-26MM










































Reviews: