background image

Exsamples of the application

Thank  you  for  choosing                       GSM   -  remote-controlled 
contact-   and   surveillance  device.  Connected  to  the   thermostat 
HandyHeat131 it controls the electrical heating system in the house,
cottages, summer houses and caravans.

The communication to the device is performed  by  SMS text from
up to 6 mobile phones, one of which is the master number.  At the
same time up to 6 people can control and surpervise the system.

 - 

Temperature 

control

 

- Free of charge burglar alarm 

 

- Remote readout of room temperatur

 

- Remote surveillance of water pipes

Start-up of HandyHeat GSM

A SIM-card is not included in the set so it should be bought separa- 
tely and with the option to top-up its account.

Unlock of SIM-card:

SIM card should be unlocked,i.e. one should just delete the PIN-
code. The SIM-card should be put in the moble phone and in the  
menu the PIN-code should be deleted. Afterwards the SIM-card is  
put back to the HandyHeat GSM. 

Change / RESET of masternumber

When a new SIM-card is used or the numbers on the SIM-card are 
doubtful, the SIM-card itself can be reset.  Leave the SIM-card  in
the holder, remove the battery and switch off the current. Press the 
RESET button in the  upper right corner for 3 seconds. Afterwards
SMS  with  the  text  OUTPUT=00 is sent from the master number.
From now on the master number has the place  NUM 1  in the me- 
mory.   Nobody  else has access to the device before Service num-
bers are typed in. The service numbers get the places from NUM 2 
til NUM 5.
Start-up:
When the device is activated the text with an actual status  is sent 
 to all the numbers from the list in the SIM-card (first 6 numbers 
 in the memory of the SIM-card ) and the alarm is activated.

By the command ”LANGAUGE=1” the language  number 1
is chosen, e.g. Danish.
By the command ”LANGAUGE=2” the language number 2 
is chosen, e.g. English.
By the command ”LANGAUGE=3” the language number 3
is chosen, e.g. Spanish.
By the command ”LANGAUGE=4“ the language number 4
is chosen, e.g. Turkish.
By the command ”LANGAUGE=5” the language number 5
is chosen, e.g. Swedish.
By the command ”LANGAUGE=6” the language number 6
is chosen, e.g. Finnish.
The device reports with the text ” Language number=x” where 
x is a number of the chosen language.
NB: Use only CAPITAL LETTERS in the text of SMS.

Alarm:

When alarm is activated the actual status of entrances is saved.
If the entrace data is changed  an alarm SMS is sent with all the 
changes. At the same time alarm is deactivated  and the coming 
changes cannot be registered. This SMS is sent to all numbers in
the list. By the start-up the alarm is activated.

GSM

Instruction manual

DANSK VARMEKABEL A/S

DANSK VARMEKABEL A/S

Language settings

 SMS 

command

 

Function  

SMS 

report

 

Outcome 

position

 

Relay 

position 

 

TEMP  

Read out the temperature
room  

temp= xx.xC  

 

 

HEAT ON

 

Heating is on. 
Temperature is acoording 
to the thermostat´s settings.

 

?  HEAT ON 

 

No signal on 
Pilot wire exit

 

Relay 1 
deactivated / 
Relay 2 deactiv.

 

HEAT OFF 

 

Heating is off. 

 

?  HEAT OFF 

 

Positive 
half of periods on 
Pilot wire exit

 

Relay 1 
deactiv. / Relay 
2 activated

 

4 NIGHT 

 

Temperature is sinking for  
3,5 degrees.

 

?  NIGHT

 Positive/negative 

periods on Pilot 
wire exit

 

Relay 1 activat. 
/ Relay 2 
activated

 

FROST  

 Sinking of the temperature  
for 7 degrees. 

 

?  FROST  

Negative 
half of periods on 
Pilot wire exit

 

Relay 1 activat. 
/ Relay 2 
deactivated

 

ALARM ON

Air sensor is activated

 ? 

ALARM 

ON 

 

The text message is
sent with activating 
an entrance 

 

 

7 ALARM 

OFF 

 

Air sensor is deactivated.

 ? 

ALARM 

OFF 

 

The text message is
sent with activating 
an entrance 

 

 

 

By activating of 
entrance (e.g. 2) and 
alarm is connected

 

Alarm alarm=in2 

changed !! 
ALARM 
OFF !! 

 

 

 

 

Message to the device  

Answer from the device

 Explanation  

STATUS  

status=HEAT ON / 
ALARM ON 
/out3 off/out4 
off/in1 off/in2 off/in3 off/in4 
off/main on (11.1V) 
/Signal=24 
 

This is the message, that  informs about the actual status 

 

of the system for the moment it is sent. It is usually used 
as a report for  the receiving messages.  It is send auto-
matically to all the numbers from the list. (11.1V) means 
that there is a net service. If the battery is in use it should 

 

be minimum7.0V otherwise the system will stop working
Signal=24 means that there is a cover for 24 at the mo-  
ment by the scale  from 0 til 30. The signal under 10 is 
not so good.

 

 

SETNUM=2+4512345678 

 

 

 

Encoding of the service 45 12345678 for 
plce 2 in the memory list. “+”is obligatary before the 

 

landline code. Place 1 is taken by the master number.

 

DELNUM=2 

 

Example for deleting of the service number 2

 

LISTNUM 

Svar 1: NUM 2=+4512345678

 

Svar 2: NUM 3=00 
Svar 3: NUM 4=00 
Svar 4: NUM 5=00 
Svar 5: NUM 6=EMPTY

 

 

5 text messages are sent to the master number  informing 

 

what service number are  in the memory list of the SIM- 
card. The service number 2 is with the Danish landline 
code +45 and telephone number 12345678.The numbers 
from 2 til 4 are deleted and number 5 is empty.  

LANGAUGE=1

 Language 

number=1

 

Language settings. 1  Danish

 

 

LANGAUGE=2

 Language 

number=2

 

Language settings. 2  English

 

 

 

 

no main! running on battery 
(max 1 hour)(08.8V) 

If the network disappears the text message is sent to all
the numbers from the list. To save the  energy all relays
are deactivated. There is only 1 hour  work capacity on  
the internal battery. SMS is sent when network is back. 

 

 

Reviews: