manualshive.com logo in svg

handi quilter Fusion QM32469, User Manual, Page: 31 / 46

Share
Download
handi quilter Fusion QM32469 User Manual Download Page 31

02/10/2015

www.HandiQuilter.com

HQ Fusion User Manual  | 31

Motor Speed Sensor Test

The Speed test helps you determine whether

or not there is a problem with the HQ Fusion speed

sensor. Before performing this test, remove the 

bobbin case and the top thread. 

Press the Start button and the machine needle 

will begin moving at 1200 stitches per minute. The 

white box will show a number that should stabilize 

at 100 if the sensor is functioning properly. Pressing 

Start again will stop the machine.

Press 

X

 to close this window or 

Back

 to return to 

the Diagnostics Menu.

 

Speed

35% 

Needle Position

Manual

Regulated

80

Presets

35% 

50% 
70% 

REC

Diagnostics

X

Diagnostics

Speed Sensor Test

Passing Test:

   The value stabilizes at 100.

Remove bobbin case and top thread.

Clear all objects from the needle

area. Press the start button

0

Calibrate Tension Test

You should only calibrate the tension under the 

direction of Handi Quilter technical support. 

While calibrating the tension, you will be asked to 

do the following:

 

1. 

Remove the tension knob. 

2. 

Gently press the spring against the tension discs 

while not compressing the spring. 

3. 

While holding the spring in place, press Reset. 

4. 

When calibration is complete, replace the 

tension knob.

Speed

35% 

Needle Position

Manual

Regulated

80

Presets

35% 
50% 

70% 

REC

Tension Calibration

X

Diagnostics

Reset

Calibration should only be done under the

guidance of a Handi Quilter Technician.

Carefully remove tension knob.

Gently press spring against tension

discs but do not compress the spring.

While holding spring in place,

press the Reset button.

Replace the tension knobs.

256

Alarms

The HQ fusion has two  useful alarms: thread-break alarm and overspeed alarm. Touch the Alarm button 

and then select either the thread-break alarm or the overspeed alarm enable or disable the alarm.

Thread-Break Alarm

• 

Press the alarm button to enable. When enabled the button turns light 

yellow. An alarm will sound if the top thread breaks. 

 

Speed

35% 

Needle

Position

Manual

Regulated

Overspeed Alarm

The overspeed alarm notifies you of an overspeed condition. This occurs if you are moving the machine 

too fast for the stitch regulation to effectively maintain even stitches while quilting. More stitches per 

inch means that you will need to move the machine slower to avoid an overspeed condition. Fewer 

stitches per inch means you can more the machine faster before encountering an overspeed condition.

Summary of Contents for Fusion QM32469















































Reviews:

No comments