*#1
LESLIE SWITCH
Owner’s Manual
Attaching the CU-1 to the XK-3/3C
%7
Th
ank you and congratulations on your purchase of the
Hammond CU-1 Leslie switch. Th
e lever switch on the
“Half-Moon” shaped CU-1 unit is used to control the Leslie
eff ects just like on the original B-3. Please read the installa-
tions instructions carefully before you install the CU-1.
Purchased items:
CU-1 unit
(w/2 Thumb screws) ................. 1
Spacer ............................................ 1
Setting up the XK-3/3C
For your safety, please operate your Hammond prod-
uct on a level, stable surface.
1. Attaching the CU-1 unit.
Remove the protective paper from the adhesive tape on the spacer,
and attach the spacer to the CU-1 unit as shown above.
No spacer is needed for mounting the CU-1 Unit on the Lower Key-
board Unit XLK-3.
Th
e CU-1 can be mounted to the front rail of the XK-3/3C is two dif-
ferent locations. Chose the location that is most comfortable to you.
Line up the screws attached to the CU-1 unit with the pair of chosen
holes located on the bottom side of the XK-3/3C’s front rail and se-
curely tighten these screws.
NOTE: Do not place the XK-3/3C with the CU-1 unit attached onto a fl at
desk type surface. Since the CU-1 extends past the bottom of the
XK-3/3C, the CU-1 unit and front rail of the XK-3/3C could be seri-
ously damaged.
NOTE: Before placing your XK-3/3C into an ATA keyboard type case, make
sure you remove the CU-1 unit fi rst.
2. Connecting to XK-3/3C
Insert the plug on the CU-1 unit into the jack located on the rear of the
XK-3/3C labeled “Foot Switch 1”.
For other compatible model, see owner’s manual of your instrument
which attach the CU-1 for detail.
1. Go to the foot switch page.
Turn on the XK-3/3C, touch the [MENU], [4]Control and choice the
“FOOT SW” page using [PAGE] buttons.
2. Set the device for CU-1.
Select “CU-1” using [VALUE] buttons.
Th
is setting is memorized when you turn off the power.
For other compatible model, see owner’s manual of your instrument
how to set up the CU-1.
Playing with your CU-1 Switch
CHORALE:
Th
e Leslie’ s rotation speed is slow.
TREMOLO:
Th
e Leslie’ s rotation speed is fast.
STOP:
In this position, the Leslie is not rotating, It takes a few seconds for
the Leslie to completely stop rotating when switched from either the
Chorale or Tremolo positions. You can choose the Brake button while
the Leslie is in the Off position. Th
e “Brake” eff ect gets the sound of
a stopped rotor or you make select “Th
rough” which by-passes the
Leslie eff ect.
NOTE: On newer Hammond products, the speeds of the Leslie can also
be selected by means of a kick switch on the expression pedal or a
switch button on the product itself. Thus the selected speed on the
CU-1 unit may occasionally not match the action speed (slow-fast-
off ) of the Leslie. If this occurs, simply move the lever switch on the
CU-1 to the adjacent position and the actual rotor speed will then
mach the CU-1 selection.
Manufacturer:
SUZUKI MUSICAL INSTRUMENT MFG. CO., LTD.
25-12, Ryoke 2 Chome, Naka-ku,
Hamamatsu 430-0852 (Shizuoka)
JAPAN
All manuals and user guides at all-guides.com
