Hamilton Beach Professional MG03 Operation Manual Download Page 5

5

Other Consumer Safety Information

This product is intended for household use only.

 w

 

WARNING

 Entanglement Hazard: 

 

To avoid serious injury do not reach 

into grinder inlet.  Always use stomper.  Do not operate without tray in place. 
The length of the cord used on this appliance was selected to reduce the 

hazards of becoming tangled in or tripping over a longer cord.  If a longer 

cord is necessary, an approved extension cord may be used.  The electrical 

rating of the extension cord must be equal to or greater than the rating of the 

appliance.  Care must be taken to arrange the extension cord that it will not 

drape over the countertop or tabletop where it can be pulled on by children 

or accidently tripped over.  Carry the unit by the motor housing with both 

hands.  Do not carry by the tray or neck.

NOTE:

 

This machine is equipped with motor overload protection. If the 

motor stops during operation due to overheating, unplug and allow it to cool 

down for approximately 30 minutes. Plug machine back in to resume normal 

operation.

Recycling the Product at the End of Its Service Life

The wheeled bin symbol marked on this appliance signifies 

that it must be taken over by a selective collection system 

conforming to the WEEE Directive so that it can be either 

recycled or dismantled in order to reduce any impact to 

the environment. The user is responsible for returning the 

product to the appropriate collection facility, as specified 

by your local code. For additional information regarding 

applicable local laws, please contact the municipal facility 

and/or local distributor.

Summary of Contents for MG03




















Reviews: