Halsey Taylor RC8*C Series Page 8 Owner'S Manual Download

Page: 8 / 8

PAGE 8

RC8*C RC12*C AND 14762 & 14700 CUP DISPENSER

97095C (Rev. E - 10/99)

FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620

2222 CAMDEN COURT

OAK BROOK, IL 60523

630.574.3500

PRINTED IN U.S.A.

CORRECT STREAM HEIGHT

ITEMIZED PARTS LIST

ITEM NO.

PART NO.

DESCRIPTION

170857042830

27673C

732660951550

23040C

27671C

Reference

100147140560

160270508640

45400C

161637308640

45398C

51546C

45396C

100322740560

10080C

66347C

45440C

74050011

50986C

61313C

15005C

40169C

45427C

40048C

45419C

40089C

45422C

55996C

1110166

55884C

75588C

100147140560

62223C

62257C

62300C

70896C

Basin

Basin Aztec Gold

Mounting Frame

Grill

Grill Aztec Gold

Remote Chiller Assembly

Gasket

Strainer Plate Chrome

Strainer Plate Aztec Gold

Drain Plug - Chrome

Drain Plug Aztec Gold

Bubbler Chrome

Bubbler Aztec Gold

Gasket Bubbler (2-Reqd)

Nipple Bubbler

Tube Waste RC8

Waste Line/Precooler Assy-RC12

Sound Dampening Pad (NS)

Holder Regulator

Regulator

Retaining Nut

Hex Nut Chrome

Hex Nut Aztec Gold

Button Chrome

Button Aztec Gold

Cover Nut Chrome

Cover Nut Aztec Gold

Strainer

Screw - #8 x 3/4 Type AB

Elbow Drain

Nut - Slip Joint 1-1/4

Gasket - Drain

Tube - Cu. 3/8 x 4.75

Tube - Cu. Regulator In

Tube Assy - Bubbler 8880

Fitting - Elbow

TROUBLE SHOOTING AND MAINTENANCE

CAUTION:

Cleaning of Aztec Gold Models requires special care. Outer

surfaces must be cleaned with a mild detergent or mixture of vinegar and

water only, rinsed and wiped dry. Abrasive and acidic cleaners may

eventually damage the Aztec Gold finish.

Orifice Assy:

Mineral deposits on orifice can cause water flow to spurt or not

regulate. Mineral deposits may be removed from the orifice with a small

round file not over 1/8" diameter or small diameter wire.

CAUTION: DO NOT

file or cut orifice material.

Stream Regulator:

If orifice is clean, regulate flow as in instructions.

If replacement is necessary, see parts list for correct regulator part number.

Actuation of Quick Connect Water Fittings:

Cooler is provided with lead-

free connectors which utilize an o-ring water seal. To remove tubing from the

fitting, relieve water pressure, push in on the gray collar while pulling on the

tubing.(see Fig.1) To insert tubing, push tube straight into fitting until it

reaches a positive stop, approximately 3/4".

FIG. 14

FIG. 15

BASIN

8,9,10
26

12
11

5,6,7,23

See Fig. 14

Summary of Contents for RC8*C Series









Search results

Summary of Contents for RC8*C Series

Reviews:

Related manuals for RC8*C Series

Brands by name

Popular brands

Halsey Taylor RC8*C Series, Owner'S Manual

Search results

Summary of Contents for RC8*C Series

Reviews:

Related manuals for RC8*C Series

Brands by name

Popular brands