TM: Riding Time
0H00M00S-19H59M59S, 1 Second, +/- 0.05%
The TM totals the riding time from the last RESET operation.
AVG: Average Speed
0.0–199.9KM/h (120.0 M/h), 0.1KM/h (M/h), +/- 0.1%
1. It is calculated from the DST divided by the TM; the average data counted is from the last
RESET to current points.
2. It displays an "Err" symbol when either the TM is over 100 hours or the DST is over
1,000 km (or miles). Reset the unit in order to restart.
MAX: Maximum Speed
0.0–199.9KM/h (120.0 M/h), 0.1KM/h (M/h), +/- 1%
It shows the highest speed from the last RESET operation.
TTM: Total Riding Time
0H00M–1999H59M, 1 Minute, +/- 0.05%
The TTM totals the riding time from the last ALL CLEAR operation.
ODO: Odometer
0.0–19999.9Km (Miles), 0.1Km (Mile), +/- 0.1%
The ODO accumulates the total distance as long as the bike is moving. The ODO data can be
cleared by ALL CLEAR operation only.
: SCAN
1. Auto-Scanning Display Mode
Press the MODE button
•
till the “ ” symbol is displayed. The computer will change the
DST, , TM, AVG, MAX, TTM and ODO display modes in a loop sequence automatically
every 6 seconds.
2. Fixed Display Mode
Press the MODE button
•
to turn off the “ ” symbol and select a desired display mode;
the computer will stop the auto-scanning display operation and the display mode is set.
/ : Speed Pacer
It flashes the “ ” speed pacer arrow while the current speed is higher than the average speed
and the down arrow “ ” flickers conversely.
BUTTON AND OPERATIONS
AUTOMATIC START/STOP
1. The computer will automatically begin counting , ODO, DST, MAX, TTM, TM and AVG
data upon riding and stop counting data when riding is stopped.
2. The flickering symbol “ ” indicates that the computer is at START status.
4403000000_20090423_v1
2s
2s
4s
6s
2s
4s
6s
DST CLOCK TM AVG MAX TTM ODO / ODO
6s
8 FUNCTIONS:
SPD, DST, ODO, CLK, AVG, MAX, TM, SCAN.
10 FUNCTIONS:
SPD, DST, ODO, CLK, AVG, MAX, TM, TTM, SCAN, SPEED PACER.
MAIN UNIT SETUP (Fig.1)
English
INITIATE THE COMPUTER
1. Be sure to press the All Clear (AC) key
„
to clear all stored data and initiate the
computer before using it or when replacing battery. Otherwise the unit may malfunction.
2. The LCD segments will be tested automatically after the All Clear key is pressed.
3. Press the “MODE” button
•
to stop the LCD test, then the flickering “KM/h” and
“c2155” will be displayed.
l
CALIBRATION
1. UNIT SELECTION
1). Press the “MODE” button
•
to select “KM/h” or “M/h”(Mile/h).
2). Hold the “MODE” button
•
till the flickering digit is changed to the digit “2” of the
c2155 to recognize either KM/h or M/h as desired.
2. CIRCUMFERENCE DATA SETTING
1). The default is set at 2155mm. Measure the value for your wheel (
Fig. a
) or refer to
the quick table provided in the manual for your bicycle. (
Fig. b
)
2). A quick press of the “MODE” button
•
advances the flickering digit by 1.
3). To change the flickering digit, hold down the “MODE” button
•
till the flickering digit
moves to the next digit.
4). When set up is complete, hold down the "mode" button for 6 seconds until main
screen appears (fig 2).
FUNCTIONS (Fig. 2)
: Current Speed
0.0–199.9KM/h (120.0 M/h), 0.1KM/h (M/h), +/- 1%
The current speed is always displayed on the 4 digits set when riding.
DST: Trip Distance
0.00–999.99Km (Miles), 0.01Km (Mile), +/- 0.01%
The DST function accumulates the distance data from the last RESET operation as long
as the bicycle is being ridden.
: 12HR Clock
1H00M00S-12H59M59S, 1 Second, +/- 0.05%
It displays the current time in 12HR clock.
POWER AUTO ON/OFF
To preserve battery, this computer will automatically switch off when it has not been used for about
10 minutes. The power will be turned on automatically by riding the bicycle or by pressing the button.
MODE BUTTON
•
Quickly press this button to move in a loop sequence from one basic function screen to another.
(
Fig. 2
)
ALL CLEAR OPERATION (Initiate the Computer)
Press the ALL CLEAR (AC)
„
key to initiate the computer or use ALL CLEAR if any irregular
data appears. It will clear all stored data.
RESET OPERATION
1. Hold down the “MODE” button
•
till the LCD digit is blank, then release it. The computer
will RESET the DST, TM, AVG, MAX.
2. It cannot reset , TTM and ODO data.
RECALIBRATION (Fig. 3)
1. Change the LCD display to ODO screen, hold down the “MODE” button
•
till (about 6
seconds) it jumps into the calibrating screen.
2. Refer to the main unit setup process to adjust the circumference.
3. Hold down the “MODE” button
•
till (about 6 seconds) it jumps out the recalibration mode to
store the desired data and complete recalibration.
12HR CLOCK SETTING (Fig. 4)
1. Change the LCD display to “ ” screen.
2. Press the “MODE” button
•
till (about 6 seconds) it jumps into the clock adjusting screen to
set the clock.
3. A quick press of the “MODE” button
•
advances the flickering digit by 1.
4. To change the flickering digit, hold down the “MODE” button
•
till the flickering digit moves
to the next digit.
5. Hold down the “MODE” button
•
till (about 6 seconds) it jumps out the setting to store the
desired data and complete clock setting.
BATTERY CHANGE (Fig. c)
1. When the brightness of the LCD display is dim, it means that the battery is nearly exhausted.
2. Replace a new LR44 (Cross reference type A76, AG13 or V13GA) battery in
the compartment on the back of the computer with the positive (+) pole toward the battery
cap.
l
TROUBLE SHOOTING
Check the following before taking unit for repair.
l
PRECAUTIONS
1. This computer can be used in the rain but should not be used under water.
2. Don’t leave the main unit exposed to direct sunlight when not riding the bike.
3. Don’t disassemble the main unit or it’s accessories.
4. Check relative position and gap of sensor and magnet periodically.
5. Clean the contacts of the bracket and the bottom of the main unit periodically.
6. Don’t use thinner, alcohol or benzine to clean the main unit or its accessories when
they
become dirty.
7. Remember to pay attention to the road while riding.
PROBLEM CHECK ITEMS SOLUTION
1. Replace the battery.
2. Be sure that the positive pole of
the battery is facing the battery cap.
1. Refer to the adjusting procedure
and complete the adjustment.
2. Wipe contacts clean.
3. Refer to (Fig. B3) and (Fig. B4) and
readjust data correctly.
4. Repair or replace wire.
5. Refer to "CALIBRATION" and enter
correct value.
Refer to the "MAIN UNIT SETUP" and
initiate the computer again.
Place main unit in the shade to return
to normal state.
No adverse effect on data.
Unit will return to normal state when
the temperature rises.
1. Is the battery dead?
2. Is there incorrect battery
installation?
1. Is it at the recalibrating or 12HR
clock setting screen?
2. Are the contacts between the
main unit and the bracket poor?
3. Are the relative positions and gap
of sensor and magnet correct?
4. Is the wire broken?
5. Is the circumference correct?
Did you leave main unit under
direct sunlight when not riding
the bike for a long time?
Is the temperature below 0°C
(32°F)?
No display
No current
Speed or
incorrect
data
Irregular
display
LCD is
black
Display is
slow
AC
4
c.
Tire Size
Circumference
Number
Tire Size
Circumference
Number
Tire Size
Circumference
Number
18 Inch
1436 mm
20x1.75
1564
20 Inch
1596
22 Inch
1759
ATB 24x1.75
1888
24 Inch
1916
24x 13/8
1942
ATB 26x1.40
1995
ATB 26x1.50
2030 mm
ATB 26x1.75
2045
26Inch (650A)
2073
ATB26x2.0(650B)
2099
700C TUBULAR
2117
700x20C
2092
700x25C
2124
700x28C
2136
POPULAR TIRE CIRCUMFERENCE REFERENCE TABLE
b.
27 Inch (700x32c)
2155 mm
700x35C
2164
700x38C
2174
27.5 Inch
2193
28 Inch (700B)
2234
28.6 Inch
2281
1~3~1
1~3~1
151624 Halfords 8 Function Computer
151632 Halfords 10 Function Computer