HALE AP Technical Manual Download Page 110

Page: 110 / 177

Inspect and clean all components. See paragraph 5.7.7, Cleaning And In-

spection Guidelines.

Inspect oil seal, if inspection indicates replacement is required see para-

graph 5.8.4.13.1, Oil Seals.

Inspect and measure clearance rings, If inspection indicates clearance

rings require replacement see paragraph 5.8.7.2, Pump Clearance Ring

R&R.

Inspect and measure impeller, if inspection indicates impeller requires

replacement see paragraph 5.8.4.6 (MBP), 5.8.4.7 (AP), or 5.8.4.8 (CBP).

If pump is an MBP and inspection indicated inducer replacement is re-

quired see paragraph 5.8.4.5.

No need to inspect mechanical seal, O-rings, and gaskets as their re-

placement is ALWAYS required.

Pump Head Installation

Prepare pump head for installation.

Install new O-ring.

Lubricate O-ring. Refer to Table 20.

Install new O-ring on pump head on gearbox side.

Install pump head on gearbox, do not damage oil seal or pump shaft.

Secure pump head to gearbox.

Install four washers.

Install four (4) M12 x 1.75 full nuts.

Using a 3/4-in (19 mm) wrench tighten (CW) four (4) M12 x 1.75 full nuts.

Using a cross pattern, torque nuts. Refer to Table 22 for recommended

torque values for fastener size and material.

With only the pump head installed on the pump, use the instructions in paragraph 5.8.4.9, Me-

chanical Seal R&R, and paragraph 5.8.4.6 (MBP), 5.8.4.7 (AP), or 5.8.4.8 (CBP) to install the seal

and impeller. If the pump is an MBP, install the inducer, see paragraph 5.8.4.5. Then install the

volute and test the pump as described in paragraph 5.8.4.3 or 5.8.4.4, Volute R&R.
5.8.4.12

RSD Pump Head R&R

As stated in paragraph 5.8.4.11, do not confuse oil or water leaks for a pump head failure. (See

AP/CBP/MBP Pump Head R&R on page 96 for full details.)
This procedure ONLY applies when the pump head requires removal from the gearbox. Prior to

performing this procedure, remove the RSD volute as described in paragraph 5.8.4.2, RSD Vol-

ute R&R. Then remove the inducer as described in paragraph 5.8.4.5, and the impeller as de-

scribed in paragraph 5.8.4.6, MBP/RSD Impeller R&R, and the mechanical seal as described in

paragraph 5.8.4.10, RSD Mechanical Seal R&R.
Refer to Table 36 for a list of tools and/or consumables required for this procedure.

Summary of Contents for AP


















































































































































































Search results

Summary of Contents for AP

Reviews:

HALE AP, Technical Manual, Page: 110 / 177

Search results

Summary of Contents for AP

Reviews: