Fuse
Power switch
J-shaped waste collector
Hexagon wrench
Spatula
Solder pot mounting
screws (both sides)
Solder pot
Power cord
Display
Control buttons
UP
DOWN
http://www.hakko.com
5. OPERATION
4. INTIAL SETUP
* Only a 50 × 50 square solder pot is included in this product.
* The 75 × 75 square solder pot is an optinal part.
* Specifications and design are subject to change without notice.
1. Install the J-shaped waste collector to the unit.
(Three-way installation is possible to meet your
operating needs.)
2. Cut the solder sticks into small pieces and put
them in the solder pot.
3. Plug the power cord into a grounded wall socket.
CAUTION
Make sure the power switch is off before plugging
in the power plug.
HAKKO FX-301B
1
Spatula 1
J-shaped waste collector
1
Hexagon wrench
1
Instruction manual
1
Power consumption
Temperature range
Solder pot dimensions
Molten solder capacity
Weight
(w/o solder and cord)
Outer dimensions
75 × 75 Square
200 - 380℃ (400 - 720℉)
75 (W) × 75 (D) × 52.5 (H) mm (3.0 × 3.0 × 2.1 in.)
1.2 kg (2.64 lb.)
Display and operation
●
Display
The front panel of the HAKKO FX-301B soldering
pot has the following controls:
- Increases the value in the appropriate display
window.
- decreases the value in the appropriate display
window.
- Holding down the button for one second or
more will enter into the temperature setting
mode. If the button is otherwise pressed for
only less than one second, the current set
temperature will remain displayed. In the input
mode, establish the entered value and exist
the data input mode.
- Holding down the button for one second or
more will enter into the offset input mode. If
the button is otherwise pressed for only less
than one second, the current offset value will
remain displayed.
Operation
1. Turn the power switch ON.
2. The temperature set at factory is displayed.
*The temperature was set to 350℃ at factory.
3. The temperature control is started, causing the
temperature to increase.
NOTE:
The display blinks when the power is turned
ON or when settings are changed. This
blinking occurs because the temperature
control is in progress. The current temperature
will be displayed in a short time.
6. PARAMETER SETTINGS
Before changing the setting temperature
The HAKKO FX-301B comes from the factory with
the following values preset:
●
Entering the parameters
1. ℃ or ℉ temperature display selection
2. Setting a solder type
Once a solder type close to the applicable one
as shown in the right side, the temperature
control will be performed for that solder type.
The HAKKO FX-301B has the following four parameters:
1) ℃ or ℉ temperature display selection
2) Setting a solder type
3) Setting the solder pot type
4) Setting the timer
Once you enter the parameter setting mode, the
setting sequence will start in the following order.
After all the parameters have been set, the
displayed temperature setting starts blinking and
the temperature of the solder pot starts rising.
1. Turn the power switch OFF.
2. Press and hold down the and buttons
simultaneously, and then turn the power switch
ON.
3. When you enter the parameter setting mode,
is displayed.
4. Press the or button to select for ℃
or for ℉.
After checking the displayed selection, press the
button.
After establishing the temperature unit to use,
enter the solder type selection mode.
Press the or button to select the number
corresponding to your solder type as follows:
Sn-Pb (Tin an lead)
Sn-Ag-Cu (Tin, silver, and copper)
Sn-Cu (Tin and copper)
Sn (Tin)
After checking the displayed selection, press the
button.
NOTE:
The solder types are listed for only rough classifica-
tion. Select the closest one to your solder type.
Instruction Manual
1. PACKING LIST AND PART NAMES
SOLDERING POT
Thank your for purchasing the HAKKO FX-301B soldering pot.
Please read this manual before operating the HAKKO FX-301B.
Keep this manual readily accessible for reference.
Please check to make sure that all items listed
below are included in the package.
2. SPECIFICATIONS
100V - 200W, 110V - 260W, 120V - 290W, 220V - 240W, 230V - 260W, 240V - 280W
143 (W) × 100 (H) × 220 (D) mm (5.6 × 4.0 × 6.7 in.)
Observe the following precautions to ensure safety.
3. SAFETY INSTRUCTIONS
Warnings, cautions and notes are placed at critical points in this manual to direct the operator’s
attention to significant items. They are defined as follows:
CAUTION : Failure to comply with a CAUTION may result in injury to the operator, or damage to the
items involved. Two examples are given below.
WARNING: Failure to comply with a WARNING may result in serious injury or death.
CAUTION
The molten solder in the solder pot is dangerous since it reaches about
450℃/842℉. The pot cover also becomes a high temperature when the
power is ON. Wrong handling may cause burns or fire. Be sure to observe
the following precautions.
●
Use this product on highly stable metal workbench. Never
use it near paper or other flammable materials.
●
Inform others in the area that the product is hot and should not be touched.
●
Never put water in the solder pot as this will cause solder to
spatter out of the solder pot.
●
Turn the power off when not in use, or left unattended.
●
Before changing parts or storing the unit, be sure to turn the
power off and allow the unit to cool to room temperature.
●
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in safe way and understand the
hazards involved.
●
Children shall not play with the appliance.
●
Cleaning and user maintenance shall not be made by
children without supervision.
●
The unit is for a counter or workbench use only.
Observe the following precautions to prevent accidents or damage to the unit.
●
Do not use the HAKKO FX-301B for applications other than soldering.
●
Do not modify the HAKKO FX-301B.
●
Use only genuine HAKKO replacement parts.
●
Do not allow the HAKKO FX-301B to become wet, or use it with wet hands.
●
Be sure the work area is well ventilated. Soldering produces smoke.
●
Do not do anything else that might be dangerous.
WARNING
WARNING
When the power is ON, the temperature of the melted solder in the solder pot is approximately
450℃/842℉. Before changing the solder pot, be sure to unplug the power cord and let the solder
and the unit cool to room temperature.
℃ or ℉ temperature display
selection
Setting a solder type
Setting the solder pot type
Setting the timer
1 C
2 1
3 1
4 0
℃
Sn-Pb (Tin an lead)
50×50 square
OFF or disabled
50 × 50 Square
200 - 450℃ (400 - 840 ℉)
50 (W) × 50 (D) × 43.5 (H) mm (2.0 × 2.0 × 1.7 in.)
0.85 kg (1.87 lb.)
1.7 kg (3.74 lb.)
2016.9
MA01633XZ160926
印刷電路板
插頭
© 2007-2015 HAKKO Corporation. All Rights Reserved.
OVERSEAS AFFILIATES
U.S.A.: AMERICAN HAKKO PRODUCTS, INC.
TEL: (661) 294-0090 FAX: (661) 294-0096
Toll Free (800)88-HAKKO
4 2 5 5 6
http://www.hakkousa.com
HONG KONG: HAKKO DEVELOPMENT CO., LTD.
TEL: 2811-5588 FAX: 2590-0217
http://www.hakko.com.hk
E-mail:[email protected]
SINGAPORE: HAKKO PRODUCTS PTE LTD.
TEL: 6748-2277 FAX: 6744-0033
http://www.hakko.com.sg
E-mail:[email protected]
Please access to the following address for the other Sales affiliates.
http://www.hakko.com
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL:+81-6-6561-3225 FAX:+81-6-6561-8466
http://www.hakko.com E-mail:[email protected]
This product includes such features as electrically conductive plastic parts and grounding of the unit
as measures to protect the device to be soldered from the effects of static electricity. Be sure to observe
the following instructions:
1. The plastic parts are not insulators, they are conductors. When making repairs or replacing
parts, take sufficient care not to expose live electrical parts or damage insulation materials.
2. Be sure to ground the unit during use.
CAUTION
This product is ESD-protected. Be sure to use a
grounded wall socket.
