manualshive.com logo in svg

Haivision Makito X4, Installation Manual, Page: 32 / 39

Share
Download
Haivision Makito X4 Installation Manual Download Page 32

www.haivision.com

Makito X4 Encoder 1.1

Makito X4 Rugged Encoder Installation Guide

32

Generated on: 2024-02-08 22:26:05

HVS-ID-IG-MX4ER-11, Issue 01

•

•

Video Input Connectors

The Makito X4 Rugged video encoder supports four (4) 

video inputs. The port marked 

SDI1 can support 

input up to 6/12G-SDI. 

The ports marked CVBS/SDI support up to 3G-SDI or analog video (NTSC/PAL).

 

 

SDI is governed by SMPTE 259M (SD-SDI), 292M (HD-SDI) and 424M (3G-SDI) standards. Each 
coaxial pin is 75ohm impedance (3-GHz bandwidth).
Composite video allows for NTSC and PAL input signals among others. 

The requirements for external cable assemblies are as follows (assuming the customer wants to avoid 
water immersion on them):

BNC Coaxial Cable Assemblies  

The cable assemblies must be waterproof. We recommend using waterproof compression type BNC 
connectors for better reliability and mechanical properties. We suggest use of a connector such as the 
Belden p/n FSNS6BNCU with a cable retention force of 40 lbs. per SCTE IPS SP401.

The input impedance must be 75 Ohms.

Note

We recommend that you keep the protective cap on any unused video connectors.

Summary of Contents for Makito X4








































Reviews:

No comments