manualshive.com logo in svg

Haivision Kraken CR, Installation Manual, Page: 2 / 14

Share
Download
Haivision Kraken CR Installation Manual Download Page 2

Kraken CR Installation Guide

Connecting the Kraken CR

HVS-ID-IG-KRAK-CR-26, Issue 01

Page 2 of 14

CAUTION  

The power supply cord is used as the main disconnect device. Ensure that the socket-outlet 

is located/installed near the equipment and is easily accessible. 

ATTENTION 

Le cordon d'alimentation est utilisé comme interrupteur général. La prise de courant doit 

être située ou installée à proximité de l'équipement et être facile d'accès.

Connecting the Kraken CR

1.

Connect an RJ45 Ethernet cable (CAT5) cable to the 

Eth 0

 connector on the Kraken CR front, shown follow-

ing.

Connect the other end of the cable to the network. This will allow you to connect to the unit via the Web 
interface or SSH.

Kraken CR - Front

2.

To configure the Kraken CR to capture CoT or KLV metadata from the serial port, connect the 

COM

 port to 

the serial port of a computer. 

Use the RS-232 DB9 to RJ45 Serial adapter (included in the package) and a standard straight Ethernet cable. 
For the pinouts, see 

“COM Serial Port RJ45 Pinout”

 and 

“Serial Adapter DB9 Pinout”

 on page

 12.

Serial Input 
(adapter supplied)

Ethernet connector

USB 2.0
(Keyboard & mouse)

Air Vent (Intake) 

Mini DisplayPort 
(Console UI)

Power On LED

SSD Drive

Summary of Contents for Kraken CR















Reviews:

No comments