manualshive.com logo in svg

Hainbuch TOPlus mini, Operating Instructions Manual

Share
Download
Hainbuch TOPlus mini Operating Instructions Manual Download Page 63

TOPlus mini / TOPlus premium pull-back 
Installation  

Order h49 7144.907-333 

 

 

63 

 

 

7.4  Preparation of the machine for installation 

1.  Set the machine into set-up mode. 

 

 

INFORMATION 

The minimum operating pressure is reached when the 
drawtube can still just be moved without triggering an 
error message. 

 

2.  Reduce the operating pressure to a minimum. 

3.  Remove  cutting  tools  and/or  sharp  objects  from  the 

working area of the machine, or cover them. 

7.5  Installation of the product 

 

 

A 

Drawtube adapter 

B 

Spindle flange 

B1  Fixing screws, spindle flange 
B2  Transport thread spindle flange 
C 

Functional unit 

C1  Fixing screws functional unit 
C2  Screwdriver bit with tip guide 
C3  Transport thread functional unit 
a 

Test surface face run-out spindle flange 

b 

Test surface axial run-out spindle flange 

c 

Test surface axial run-out functional unit 

d 

Test surface face run-out functional unit 

 

Special aids needed: 

 

Screwdriver bit with tip guide 

1.  As described in the »Preparation of the machine for in-

stallation« chapter, prepare for the following steps. 

 

 

 

 

Summary of Contents for TOPlus mini

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands