background image

Before using

Automatic Drum Washing Machine

Table of Contents

During using

Maintenance

Names of parts---------------inside front cover

Matters needing attention-------------------1-3

Installation---------------------------------------4-5

Control panel--------------------------------------6

Operational functions-------------------------6-7

Program selection-----------------------------8-9

Washing methods------------------------------11

Additional information-------------------------12

Maintenance-------------------------------------13

Trouble shooting--------------------------------15

Wiring circuit-------------------------------------17

Technical specification------------Back cover

Warning-------------------------------------------16

Warning code------------------------------------14

Operation

Manual

Main power

Max working current(A)

Water pressure(MPa)

Washing power(W)

Spining power(W)

Washing capcity(Kg)

Spinning speed(rpm)

Drying power(W)

Size(high,depth,width)mm

Weight(Kg)

0.05



P



1

300

700

5

1200/900/600

1000

850

‚

550

‚

595

78

XQG50-S1216

Item

Model

XQG50-S1216

Technica specifications

Preparations-------------------------------------10

220V~/50Hz

10

Summary of Contents for XQG50-S1216











Reviews: