Haier XPB10-LAP User Manual Download Page 1

2

Safety precautions

Please insert the power cord into
special receptacle with rated vol-
tage.Be sure to use single-phase
 three pins  receptacle.The earthing
 terminal of the receptacle must be
 earthed reliably.If possible,please
adopt electric leakage protector.

When the machine is normally
using, please put the power plug
at the location easily to be insert-
ed and extracted by hand. Be sure
to pull the plug off when there's
power failure, or the machine is
being moved, cleaned or when it
is idle.

If  the power cord is bad, to avoid risk it is required to replace it by the 
technicians ofour special shop or the after-sale service department.
Keep the pin of the power plug clean.

Earth

Do  not  put  the  machine  at  damp
place like  the  bathroom .  Never
wash  it   with water. Do not place 
wet laundries on the control panel.

Do not use water hotter than 50 C .

In case the washing  machine is  installed
on  ground  with  carpet ,  do not block the 
ventilation  hole  with  carpet.

Do not wash water-proof laundries like
the raincoat,  bike  covers etc. to avoid 
abnormal vibrations  in spinning.

Do not let the machine share one receptacle
with  other electric  appliances. If  the  power
plug  is  damaged,  or  the  plugging  into the
receptacle  is loose, do not use the plug any
more.

Ventilation hole at 
the  bottom of the 
washing machine

Twin-tub Washing Machine 

User's   manual

This manual is for

Please read this manual 
carefully before using. 
Retain it for future reference.

Summary of Contents for XPB10-LAP










Reviews: