background image

PJF2-200

PJF2-300

OPERATION INSTRUCTION

Haier solar water heater

OPERATION INSTRUCTION

Haier solar water heater

Please read this operating instruction 
carefully before use.
Please store it properly for the reference.

HC

SOL H

WT

PRE INT

T-DISP

SET

REG

MODE

ON/OFF

MPa

Safety Consideration  

(Read it carefully before use)

 ..............................................

2

Installation introduction ..............3

Installation Consideration ............3

Installation of Solar Collector ......3

Installation of Storage Water Tank ....5

Installation of the solar station ...5

Installation of expansion water  

tank and priming valve .................6

Priming antifreeze ...........................6

Circuit connection ...........................7

Pipeline Connection .......................8

Directions for use ...........................9

Directions for buttons and  

indication lamps ................................ 9

Operation methods ........................ 11

Cleaning and Servicing ................13

Electrical Diagram•Technical Data

 ...14

Electric principle diagram ............14

Technical Data ..................................14

FAQ .................................................15

Packing list ....................................16

Summary of Contents for PJF2-200

















Reviews: