Haier GE DDT700S N0 Series Technical Service Manual Download Page 54

Page: 54 / 78

– 54 –

•

Turbidity Sensor

: 5 VDC to LED, 10k ohms

•

Thermistor

(in turbidity sensor)

• Spray Arm Rotation

Circulation System

Spray Arm RPM

Lower

50 RPM CW +/- 10%

Middle

30 RPM CCW +/- 10%

With only .80 gallons of water, filtration is the start of improved performance. Water is cleaned through

the fine and ultra-fine filters before it enters the main pump. Water must also flow through the Piranha

Hard-Food Disposal and finally into the wash pump assembly. Clean filtered water then flows into

the diverter system which directs it to either the lower spray arm or mid spray arm and upper sprayer.

Water is jetted through more jets and with more power due to different wash zones created by the

diverter.

This section will discuss wash system filtration, operation, components, removal procedures and

diagnostics. The new 2019 Stainless Steel Tub Dishwasher features alternating spray arms allowing

low water use, helping energy efficiency. A diverter system is used to isolate the wash arms and is

controlled by cycling the wash pump as described later in this section. Some models have a wash

zone feature which allows the consumer the flexibility of washing in the lower or upper racks only.

Using this feature will shorten the cycle time by 30%. When Bottle Wash is selected, the upper rack

time is increased allowing the bottle wash feature to be used for maximum cleaning. Filtration has

been greatly improved to allow clean filtered water to circulate during wash. The fine and ultra-fine

filters are consumer removable and cleanable.

Specifications

•

Single Speed Circulation Pump

: 120 VAC,

.8 amps – 3.8 LRA, 8 GPM @ 5PSI

• Heater

: 120 VAC, 18 ohms wet – 28.8 ohm

dry, 6.67 amp wet -4.17 dry, Watts 800 wet

/500 dry +/- 5%

•

Detergent Cup

: 13.5 VDC, 32 ohms, .5

second to release detergent cup, 15 seconds

to release Rinse Aid (see the

Door

section of

Tub and Structure

in this service guide).

Bottle Wash Cover

Bottle Wash Manifold

Bottle Wash Clip

Mid Conduit

Mid Spray Arm

Lower Spray

Arm

Ultra-Fine Filter

Sump

Upper Spray System

Bottle Wash Hose

Main Conduit

Docking Cone

Diverter Top

Check Ball

Fine Filter

: Clockwise

CCW

: Counter-Clockwise

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands