Haier GE DDT700S N0 Series Technical Service Manual Download Page 34

Page: 34 / 78

– 34 –

Appearances may vary throughout this service

guide. Some models do not have all features

shown or may be different depending the model

number.

Components

Bar Handle

The bar handle is attached to the outer door

panel. The handle is an assembly with end caps

pre-attached.

Bar Handle Removal

1. Remove and separate the door.

2. Remove two 3/8-in. hex-head screws holding

the handle.

To remove the hinges from the outer door panel,

remove six 1/4-in. hex-head screws.

Lens

Handle

Handle Screws

Handle Brackets

Hinge Screws

Hinges

Badge

Some models have a pocket handle mounted to

the outer door panel.

To remove the pocket handle, remove seven 1/4-

in. hex-head screws.

Outer Door Panel

Pocket Handle

Hinges

Summary of Contents for GE DDT700S N0 Series















































































Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands

Haier GE DDT700S N0 Series, Technical Service Manual

Search results

Summary of Contents for GE DDT700S N0 Series

Reviews:

Related manuals for GE DDT700S N0 Series

Brands by name

Popular brands