background image

After reading this handbook, hand it over to those who will be using the unit.

The user of the unit should keep this mamual at hand and make it available to those who will be

performing repairs or relocating the unit. Also, make it available to the new user when the user changes

hands.

WARNING

CAUTION:

2

Ask your dealer or qualified personnel to carry out installation work.Do not attempt to install the air

conditioner yourself. Improper Installation may result in water leakage, electric shocks, fire or explosion.

All the cables shall have got the European authentication certificate. During installation, when the

connecting cables break off, it must be assured that the grouding wire is the last one to be broken off.

If refrigerant gas leaks during installation, ventilate the area immediately.oxic gas may be produced.if the

refrigerant comes into contact with fire,and explosion may be happen.

Make sure ground connection is correct and reliable.Do not earth the unit to a utility pipe, lightning

conductor or telephone earth lead. Imperfect earthing may result in electric shocks.

The breaker of the air conditioner should be all-pole switch and explosion-proof. The distance between

its two contacts should not be no less than 3mm. Such means for disconnection must be incorporated in

the wiring.

The air conditioning sockets should be placed 1m above from the air conditioner, nor under the air

conditioner. Be sure not to use open flame, high static electrical or high temperature equipments

etc.nearby the air conditioner.

Do not use means to accelerate the defrosting process or to clean, other than those recommended by

the manufacturer.

The appliance must be stored in a room without continuously operating ignition sources, the radius of the

storage area should be no less than 2.5 m (for example:open flames, an operating gas appliance or an

operating electric heater).

Do not pierce or burn.

Be aware that refrigerants may not contain an odour.

The appliance must be installed, operated and stored in a room with a floor area larger than the Minimum

Room Area specified in the table on the following pages,The room should be well ventilated.

Comply with national gas regulations.

This appliance can be used by children aged 8 years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge if they have been given superivision

or instruction concering use of the appliance in a safe way and understand the hazards involved. Children

shall not play with the appliance. Cleaning and user maintenance shall not be made by children without

supervision.

The air conditioner can not be discarded or scrapped Randomly If you need please contact customer

service personnel of Haier to scrap in order to obtain the correct disposal methods.

Reusable mechanical connectors and flared joints are not allowed indoor.

Read the precautions in this manual

carefully before operating the unit.

This symbol shows that this appliance 

uses a flammable refrigerant.

If the refrigerant is leaked and exposed 

to an external ignition source, there is a 

risk of fire.

Do not install the air conditioner at any place where there is danger of flammable gas leakage.In the event of a gas leakage,

build-up of gas near the air conditioner may cause a fire to break out.

Tighten the flare nut according to the specified method such as with a torque wrench.If the flare nut is too tight, it may crack

after prolonged use, causing refrigerant leakage.

Take adequate steps to prevent the outdoor unit being used as a shelter by small animals.Small animals.making contact with

electrical parts can cause malfunctions, smoke or fire.

Please instruct the customer to keep the area around the unit clean

The temperature of refrigerant circuit will be high, please keep the inter-unit wire away from copper pipes that not thermally

insulated.

Only qualified personnel can handle, fill, purge and dispose of the refrigerant.

 Read the operator's manual

Service indicator, read technical

manual

Summary of Contents for 3U55S2PR1FA

































Reviews: