background image

while the input is held active.  The rate at  which the input will 
repeat is the same rate dictated by the system to the keyboard.

<S>

 Use this delimeter to send the input response to the serial 

port instead of emulating keystrokes.  The sample.txt file included 
on the KE72 CD  provides extended examples of the serial port 
function.  The <S> option must follow the : or | character on the 
input definition line.

ex: 

IN05:<S>[F]

 will send an ASCII “F” out of the KE72 serial 

port  when the input #5  is  activated.  In addition to an ASCII 
character,  a  numeric  value may be specified for the byte to be 
sent.  ex: 

IN05:<S>[220]

 will send a one byte value of 0xDC.

Inputs on the KE72 may be programmed to send up to 32 keystrokes 
when activated, and up to 16 when the input is released.

example:

IN28:[p][r][e][s][s][e][d] 

  

   Types “pressed” when input 28 activates

IN28|[r][e][l][e][a][s][e][d] 

Types “released” when input 28 deactivates

The key to be emulated is always inserted between square 
brackets.  The following list summarizes the associated key names 
for keystrokes that are used in a KE72 Configuration  File.  All 
other keys are represented by their direct equivalent (ex: A = A 
key, B = B Key, etc.)

[Shift]  = 

Left Shift   [LShift] = 

Left Shift

[RShift] = 

Right Shift  

[Ctrl]  = 

Left Ctrl

[LCtrl]  = 

Left Ctrl   [RCtrl]  = 

Right Ctrl

[Alt] 

Left Alt  

 

[LAlt]  = 

Left Alt

[RAlt]  = 

Right Alt   [Esc]  = 

Escape

[F1] 

F1 key  

 

[F2] 

F2 key

[F3] 

F3 key  

 

[F4] 

F4 key

[F5] 

F5 key  

 

[F6] 

F6 key

10

message to prevent a stuck key.  The KE72 responds with a 
“!”  character after each byte is received in this mode.  Always 
wait for the “!”  acknowledgement before sending additional 
communication to the serial port.

NOTE: Serial data in and out of the KE72 serial port is always at 9600 Baud, 8 
bit characters, No Parity, and one stop bit. No hardware handshaking is used. 
Custom versions are available, please contact us with your requirements.

0xC2 

- Use this one byte command to set the serial translation 

mode to ASCII to Keystroke.  This mode is also the default mode 
at power on or reset.  The KE72 responds with “!” to acknowledge 
receipt of this command.

0xC3

 - This command will set the KE72 serial translation mode 

in Key Number to Keystroke.  While in this mode, a single byte is 
sent to the KE72 serial port which corresponds to the up or down 
state of a particular key.  Once this command byte is received by 
the KE72, the serial mode will be in the key number mode until 
changed by the 0xC2 command, a reset to the PC occurs, or the 
PC is powered down and back up.  The KE72 acknowledges re-
ceipt of this command with the “!” character.

0XC4

 - Use this command to poll the KE72 for the current se-

rial translation mode.  When the KE72 receives this command, 
a character is returned by the KE72 which indicates the current 
serial to keystroke mode.

”1”  (0x31)  is  returned in response to the 0XC4  command if the KE72 is 
operating in the ASCII to Keystroke mode.

“2”  (0X32)  is  returned in response to the 0XC4  command if the KE72 is 
operating in the Key Number to Keystroke mode.

0XC5

  -  Input state command.  When this serial command is 

received by the KE72, a string of 9 bytes are transmitted on the 
serial port which indicate the current debounced status of each of 
the 72 inputs on the KE72.  The first byte returned in response to  

17

Summary of Contents for KE72





























Reviews: