15 min
s
5 min
auto
-
+
lux
test
30
8 m
(
α
200°)
8 m
(
α
200°)
6 m
(
α
140°)
6 m
(
α
140°)
α
1
6T 7973-02a
6T 7973-02a
Warning :
This device is to be installed only by a
professional electrician fitter according to
local applicable installation standards.
Test and validation of detection
zone
Set potentiometer
2
to Test mode.
The Test mode is available for 3 minutes time
and does not take brightness level into
account.
Each detected movement turns LED
A
on for 2
seconds.
The associated receiver is not under control.
After 3 minutes without detection, the product
is set back to auto mode.
Limitation of detection zone :
You can limit the detection zone using the
shutters supplied or by inclining the head.
O
The test mode is available only once the
product has been configured.
Mounting
Projection or ceiling mount :
- Fix the wall plate using the supplied screws.
- Clip the detector onto the wall plate
- Tighten the screws to close.
For angle mounting, the wall fixing plate is
fitted between the accessory and
the detector.
Precautions for installation
Product Description and working
principles
This detector allows remote control of one
or more receivers for a given time when a
movement is detected in its detection zone.
This product can be used in two types of
configuration: one detector controls
one/several receiver(s); several transmitters
control the receiver(s).
Operation
The receiver(s) is(are) under control as soon as
the brightness level as set by potentiometer
2
is considered too low and a movement is
detected.
2 types of operation are possible:
- Only one detector controls the receiver(s) :
Upon detection, the receiver remains activated
for the time set by potentiometer
1
. Before
starting configuration, set the desired delay on
potentiometer
1
.
Follow the configuration procedure as
explained in the Configuration Instructions
supplied with the receiver and select the
"Remote control switch” function.
- Several detectors control the receiver(s) :
Après détection, le récepteur reste activé
Upon detection, the receiver remains activated
for the time set for the configuration on the
receiver.
Before starting configuration, set
potentiometer
1
to "impulse" position
.
Follow the configuration procedure as
explained in the Configuration Instructions
supplied with the receiver and select the
"Remote control switch" function.
If LED
A
flashes quickly during configuration,
the position of potentiometer
1
is not
compatible with the selected function.
Factory return
Keep push-button
J
depressed until LED
cfg
(flashes (>10s), and then release it.
LED
cfg
is turned off when factory return is
completed.
This operation causes full delete of product
configuration in any configuration mode.
After factory return, wait 15s before starting
configuration.
Configuration (button
J
)
These detectors can be configured in 3 different
ways :
•
: tool-free configuration (using product
pushbuttons and LEDs), see User's Instructions
6T7952 supplied with the product.
• TX100/B V2.6.0 or above :
description of product functions available from
the Manufacturer.
• ETS3 or via TR131 : database and description of
application software available from the
Manufacturer.
Configuration by TX100 or ETS
Set the product in configuration mode by pressing
J
button once during the teaching session of
TX100 or for addressing with TR131 in ETS.
O
Product factory return is required to change
the configuration mode.
quick
link
Description
Detection zone
TRE51., TRE53.
Installation
Adjustments
Shutters
Angle fixing support
Optimal installation height is 2.5m.
The detection zone shall remain free of obstacle.
8 m
16 m
2,5 m
0,5 m
16 m
4 m
LED
A
LED
B
Delay
(lighting time)
Brightness
level
Sensitivity
(change
of range)
§
Motion Detectors
220° solar
User instructions
¨
Action
Adjustments
Potentiometer
Use Auto (factory)
settings
to set automatic
lighting turn-on for
a given time.
Auto Settings
Put the Lux potentiometer on
“
auto test
”.
The settings are predefined :
Lux =
,
(operating at night only)
time = 3 min,
sensitivity = max
auto
lux
test
Turn automatic
lighting on for
a given time.
Installer settings
15 min
30 s
5 min
auto
-
+
lux
test
Control a timer,
a chime, etc.
Impulse
Auto settings are usable with
time = 1s.
(cannot be changed).
15 min
s
5 min
auto
-
+
lux
test
30
Test and confirm
detection zone.
Test mode
Move the potentiometer
2
to “
auto test
”
auto
lux
test
auto
lux
test
Adjust sensitivity
Allows setting the range
to avoid disturbance.
-
+
DETECTORS 220°
TRE510
White
TRE511
Anthracite
TRE530
White
TRE531
Anthracite
Hereby, hager Controls, declares that this motion detector
output is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
The CE declaration can be consulted on the site :
www.hagergroup.net
Usable in all Europe
and in Switzerland
For optimum detection conditions, please follow these recommendations :
- Keep the detector protected from solar radiation and bad weather, as it is sensitive to these
conditions.
- Maintain 1m distance between the light source and the detector and keep the detector out of the
light source.
1
2
IP55
+ 90°/- 30°
+/-80°
Wall fixing plate
Adjustment potentiometers
Directional detection head
Vertical adjustment
ACCESSORY FOR
ANGLE FIXING
EE855
White
EE856
Anthracite
52125
White
52126
Anthracite
RF
TP
230V~
Bus
30 V
J
Button
cfg
cfg
LED C
Button
J
V2.6.0
