background image

CI-1255e™ Power Amplifier

Hafler

Passion for Perfection

9

eCoSySTem™ eNeRGy SAvINGS

One of the best features with the Hafler CI-1255e is the energy-saving ECOSYSTEM 

circuit. ECOSYSTEM automatically shuts of the amplifier when no signal is detected 

after a minute. This of course saves on your electrical bill and because the amp is off, 

it also reduces the heat being generated which means a reduction in air conditioning 

costs! 

As soon as a signal is detected on any of the inputs (the global bus or individual 

channels) the CI-1255e will spring back to life in about 10 milliseconds – faster than 

you can pronounce a consonant. Best of all, ECOSYSTEM is super quiet and pop-free. 

When the ECOSYSTEM is activated, ECOSYSTEM LED will illuminate. 

AdjuSTING The LeveLS IN The vARIouS zoNeS

Each of the 12 channels is equipped with individual level controls to set the music loudness for each of the zones. There is also a full 

array of rear mounted LEDs that let you visually check to make sure you are getting a source signal when setting up the system. Using 

a cell phone or tablet as a source during setup is made easy with the 3.5mm front panel input. 

Start with the trim controls fully open (fully clockwise), and your preamp turned down. Turn on the source material and the amplifier, 

check the LEDs to make sure signal is being received, and turn up the preamp until the desired level is achieved. If any of the zones 

are too loud, you can use a tweaker or a small slot screwdriver to turn down on the associated trim controls for those channels.

The front panel is also equipped with the same array of signal presence LEDs along with a second series that shows clip levels. When 

driven into the red, it is a good idea to back down the levels in order to prevent distortion and thermal overload. 

AuTomATIC fAuLT-SAfe™ PRoTeCTIoN CIRCuITRy

Another  great  feature  that  is  built  into  the  CI-1255e  is  the  Fault-Safe™  automatic  protection  mode.  Each  CI-1255e  channel  is 

individually and fully protected against low impedance, overheating, overloading, over voltage and under voltage — should any of the 

following faults occur, the CI-1255e will automatically shut down any affected channels. The protection circuitry automatically restores 

the amplifier channel as soon as its fault returns to the safe operating range. 

Summary of Contents for CI-1255e





















Reviews: