background image

75

Sensor setup

used: 
Area x Velocity = Flow.

See Submerged Pressure 770XXX manual for sensor details.

6.3.1 Submerged area/velocity sensor programming

1.

From the Main Menu, select 

OPTIONS, LEVEL SENSOR.

2.

Select Submerged Xducer using the 

CHANGE CHOICE

 

key, then press

ACCEPT

.

3.

From the 

MAIN MENU

, select 

SETUP, MODIFY SELECTED ITEMS.

4.

Highlight Velocity Direction using the 

UP

 and 

DOWN

 keys. Press 

SELECT

.

5.

Set the velocity direction (upstream, downstream, or always positive) using the 

CHANGE CHOICE

 key. Press 

ACCEPT

 to continue.

6.

Highlight Velocity Units using the 

UP

 and 

DOWN

 keys. Press 

SELECT

.

7.

Set the Velocity Units (fps or m/s), using the 

UP

 and 

DOWN

 keys. Press 

ACCEPT

 to 

continue.

8.

Highlight Velocity Cutoff, using the 

UP

 and 

DOWN

 keys. Press 

SELECT

.

9.

Read the Velocity Cutoff information screen. Press any key to continue.

10.

Set the Velocity Cutoff using the numeric keypad. Press 

ACCEPT

.

11.

Set the Velocity Default, using the numeric keypad. Press 

ACCEPT

. Press 

RETURN

 to 

go back to the Setup Menu or the 

MAIN MENU

 to return to the Main Menu display.

6.4 Submerged pressure sensor

The submerged pressure sensor contains a submerged pressure transducer that 
measures level in an open channel flow stream. 

The submerged pressure sensor is mounted in the flow stream at the proper location for 
level measurement. As the level in the channel increases and decreases, the pressure at 
the submerged sensor varies proportionately. The pressure transducer converts the water 
pressure to a voltage. The sampler uses the voltage to calculate the liquid level in the 
channel. After calculating the level, the sampler then converts the level reading to a flow 
rate based on the user-defined characteristics of the installed primary device.

The transducer in the submerged sensor first reads the pressure in the channel, then at 
regular intervals, switches to a reference port to compare it to the atmospheric pressure. 
This pressure difference is converted to a number which represents the liquid level. At 
regular intervals, both the pressure transducer diaphragm and the reference port are 
switched to atmosphere together. Then they are electronically zeroed to eliminate any 
drift due to changing barometric pressure.

6.4.1 Submerged pressure sensor connection

The submerged pressure sensor connection is located on the left side of the controller 
housing and is labeled submerged pressure sensor. The connector is keyed and can only 
be inserted in the proper orientation (key up).

Goodnal STP ST041 Pre Treatment (Sigma 900 MAX All Weather Refrigerated Sampler) Vendor Manual

Q-Pulse Id VM373

Active 29/10/2013

Page 75 of 122

Summary of Contents for Sigma 900 MAX



























































































































Reviews: