background image

Specifications

Specifications are subject to change without notice.

Specification

Details

Dimensions (W x D x H)

37 x 30 x 170 mm (1.45 x 1.18 x 6.69 in.)

Enclosure rating

IP67 

Weight

135 g (0.297 lb) with batteries

Power requirements (internal)

AAA alkaline batteries (4x)

Battery life

450 hours

Operating temperature

0 to 50 °C (32 to 122 °F)

Storage temperature

–20 to 60 °C (–4 to 140 °F) )

Operating humidity

80% (non-condensing)

Altitude

2000 m (6562 ft)

Instrument range

Cond

LR

: 0 to 1999 µS/cm; Cond

HR

: 0 to 19.99 mS/cm

Resolution

Cond

LR

: 1 µS/cm; Cond

HR

: 0.01 mS/cm

Accuracy

Cond

LR

: ±1% FS

1

; Cond

HR

: ±2% FS

Note: Temperature calibration is not available.

Calibration points

Cond

LR

: 2 points (auto), 1 point (custom); Cond

HR

: 1 point (auto and custom)

Auto-recognition calibration standards

Cond

LR

: 147 µS/cm and 1413 µS/cm; Cond

HR

: 12.88 mS/cm

Certifications

CE mark, FCC, Industry Canada, KC Mark, RCM, China RoHS

Warranty

1 year for manufacturing faults only. Damage from use is not covered.

General information

In no event will the manufacturer be liable for direct, indirect, special, incidental or
consequential damages resulting from any defect or omission in this manual. The
manufacturer reserves the right to make changes in this manual and the products it
describes at any time, without notice or obligation. Revised editions are found on the
manufacturer’s website.

Safety information

N O T I C E

 

The manufacturer is not responsible for any damages due to misapplication or misuse of this
product including, without limitation, direct, incidental and consequential damages, and disclaims
such damages to the full extent permitted under applicable law. The user is solely responsible to
identify critical application risks and install appropriate mechanisms to protect processes during a
possible equipment malfunction.

Please read this entire manual before unpacking, setting up or operating this equipment.
Pay attention to all danger and caution statements. Failure to do so could result in serious
injury to the operator or damage to the equipment.
Make sure that the protection provided by this equipment is not impaired. Do not use or
install this equipment in any manner other than that specified in this manual.

1

Based on a 2-point calibration and the conductivity range of the calibration standards includes the conductivity
value of the water sample.

2

Summary of Contents for Pocket Pro CondLR











Reviews: