Habasit PMR-07 General Manual Use And Maintenance Download Page 10 | Manualshive

Page: 10 / 68

Habasit PMR-07 General Manual Use And Maintenance Download Page 10

Habasit Italiana S.p.A.
Vittorio Veneto 31029 (TV)
Tel.: ++39(0)438.9113
Fax. ++39(0)438.200545

Regulating Unit PMR-07

Author:

A.T. / KM

REGULATIONS AND GENERAL WARNING NOTES

Edition: 04/2006

Page

A-4

Replaces: 10/2005

A.3

USE CRITERIA

HABASIT requests the Customer to fully read this manual on delivery of the regulating unit it
accompanies, and always before attempting any action on the regulating unit. This manual is
arranged to supply all the instructions, indications and warnings the user may need in order to
know the equipment, understand its operating principles, and to be adequately informed to
ensure safe use.

In addition to the instructions in this manual, we would ask users to observe any specific current
laws.

This manual must be considered as an essential part of the equipment. It contents must be
made known to the entrusted maintenance persons and users.

The purpose is to provide all the information required for good, correct use of the equipment.

The manual must be kept throughout the equipment’s life and must be updated in the event of
modifications aimed at improving the regulating unit’s performance.

The manual must be available to qualified personnel.

Consultation of this manual is facilitated by the general index on the first page, which makes it
possible to immediately find the subject of interest.

If the subject dealt with is particularly important it is highlighted with references to the type of
technical personnel required to intervene.

All updates HABASIT considers necessary to improve the quality of the regulating unit will be
communicated by way of sending of further specific documentation or a new manual to replace
the previous one.

If the equipment is sold to another customer, the manual must accompany it and the new
customer must be notified to HABASIT for any future modifications and updates.

A copy of this manual, delivered with the equipment, is meant for the maintenance operators,
who shall read and keep it near the equipment, and consult it before undertaking any action on
the equipment.

Regulating Unit PMR-07

«
...
8
9
10
11
12
...
»

Summary of Contents for PMR-07





































































Reviews:

No comments