Habasit AT-305 General Manual Use And Maintenance Download Page 43

Page: 43 / 51

Habasit Italiana S.p.A.
Vittorio Veneto 31029 (TV)
Tel.: ++39(0)438.9113
Fax. ++39(0)438.200545

Skiving device AT-305

Author:

S.D.T. / KM

ORDINARY MAINTENANCE

Edition: 02/2005

Page

E-6

Replaces: 01/2001

E.3.5

Replacing of the wear plate

Stop the machine: press the

stop push button

[22].

Place the tip of a screwdriver in the

slots

[18] and lever out the worn

wear plate

[3].

Remove the remainders of the adhesive tape and clean the surface with solvent.

Stick double sided adhesive tape onto a new wear plate.

Place the new plate in position, align carefully and press firmly down to make sure the surface is
perfectly even.

ABLE

–

ERIODIC MAINTENANCE WORK

Operation Period

Personnel

Method

General cleaning

Daily

Operator

Clean the machine after each use.
Remove residual dust with a suitable suction
device.

Lubrication Monthly

Maintenance

worker

Lubricate the handwheel screw with a thin film of
grease. Wipe off any excess.

Check off

electrical cables

Monthly

Maintenance

worker

Check for defective insulation or connectors.

Skiving device AT-305

Summary of Contents for AT-305




















































Search results

Summary of Contents for AT-305

Reviews:

Brands by name

Popular brands

Habasit AT-305, General Manual Use And Maintenance

Search results

Summary of Contents for AT-305

Reviews:

Brands by name

Popular brands