H3C WX Series Command Reference Manual Download Page 129

Page: 129 / 200

129

This command will permanently delete the configuration file from the device. Use it with
caution.

Related commands: save, display saved-configuration.

Examples

Delete the configuration file for the next startup of the device from the storage medium
of the device.

<Sysname> reset saved-configuration

The saved configuration will be erased.
Are you sure? [Y/N]:y
Configuration in the device is being cleared.

Please wait .......
Configuration in the device is cleared.

restore startup-configuration

Syntax

restore startup-configuration from

src-addr src-filename

View

User view

Default Level

2: System level

Parameters

src-addr:

IP address or name of a TFTP server. The address cannot be an IPv6 address.

src-filename

: Filename of the configuration file to be downloaded from the specified

server.

Description

Use the

restore startup-configuration

command to download a configuration file from

the specified TFTP server to the device and specify the configuration file as the startup
configuration file to be used at the next startup of the device.

Examples

Download configuration file

test.cfg

from the TFTP server whose IP address is 2.2.2.2, and

the configuration file is to be used at the next startup of the device.

<Sysname> restore startup-configuration from 2.2.2.2 test.cfg
Restore

startup-configuration

file

from

2.2.2.2.

Please

wait..............

finished!

Summary of Contents for WX Series









































































































































































































Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands

H3C WX Series, Command Reference Manual

Search results

Summary of Contents for WX Series

Reviews:

Related manuals for WX Series

Brands by name

Popular brands