H3C WA510H Installation Manual Download Page 17

Page: 17 / 19

Appendix B LEDs and ports

LEDs

Figure 9 LEDs on the AP

(1) Power LED

(2) Radio LED

(3) Uplink LED

(4) Ethernet port LEDs

Table 3 LED description

Mark Status

Description

Power LED

Off

The AP is not powered on.

Steady yellow

An exception has occurred during AP initialization.

Flashing yellow (1 Hz)

No radio card is detected.

Flashing yellow (2 Hz)

The Ethernet interfaces are shut down and no mesh link
is present.

Flashing green (0.5 Hz)

The AP has started up but is not connected to any AC.

Flashing green (2 Hz)

The AP is updating applications.

Steady green

The AP is operating correctly.

Radio LED

Off

No clients are associated with the AP or the LED is
disabled from the CLI.

Flashing green (1 Hz)

The 2.4 G radio has associated clients.

Flashing yellow (1 Hz)

The 5 G radio has associated clients.

Alternating green and yellow
(1 Hz)

Both the 2.4 G and 5 G radios have associated clients.

Summary of Contents for WA510H




















Search results

Summary of Contents for WA510H

Reviews:

Related manuals for WA510H

Brands by name

Popular brands

H3C WA510H, Installation Manual

Search results

Summary of Contents for WA510H

Reviews:

Related manuals for WA510H

Brands by name

Popular brands