H3C WA2600 Series Command Reference Manual Download Page 61

Page: 61 / 131

8-2

For a domain name displayed with the

display dns ipv6 dynamic-host

command, no more than 21

characters can be displayed. If the domain name exceeds the maximum length, the first 21 characters

are displayed.

display dns ipv6 server

Syntax

display dns ipv6 server

[

dynamic

]

View

Any view

Default Level

1: Monitor level

Parameters

dynamic

: Displays IPv6 DNS server information acquired dynamically through DHCP or other

protocols.

Description

Use the

display dns ipv6 server

command to display IPv6 DNS server information.

Examples

# Display IPv6 DNS server information.

<Sysname> display dns ipv6 server

Type:

D:Dynamic S:Static

DNS Server Type IPv6 Address (Interface Name)

1 S 1::1

2 S FE80:1111:2222:3333:4444:5555:6666:7777 Vlan2

Table 8-2 display dns ipv6 server

command output description

Field

Description

DNS Server

Sequence number of the DNS server, which is assigned automatically by the system,
starting from 1.

Type

Type of the DNS server: “S” represents a statically configured DNS server, and “D”
represents a DNS server obtained dynamically through DHCP or other protocols.

IPv6 Address

IPv6 address of the DNS server

Interface Name

Interface name, which is available only for a DNS server with an IPv6 link-local
address configured.

Summary of Contents for WA2600 Series




































































































































Search results

Summary of Contents for WA2600 Series

Reviews:

Related manuals for WA2600 Series

Brands by name

Popular brands

H3C WA2600 Series, Command Reference Manual

Search results

Summary of Contents for WA2600 Series

Reviews:

Related manuals for WA2600 Series

Brands by name

Popular brands