manualshive.com logo in svg

H3C WA Series, Layer 2 Command Reference, Page: 66 / 133

Share
Download
H3C WA Series Layer 2 Command Reference Download Page 66

 

58

 

After configuring this command, run the 

active region-configuration

 command to activate the configured 

MST region level. 
Related commands: 

instance

, 

region-name

, 

vlan-mapping modulo

,

 display stp region-configuration

, 

check region-configuration

, and 

active region-configuration

.  

Examples 

# Set the MSTP revision level of the MST region to 5.  

<Sysname> system-view 

[Sysname] stp region-configuration 

[Sysname-mst-region] revision-level 5 

stp bpdu-protection 

Syntax 

stp bpdu-protection 
undo stp

 

bpdu-protection

 

View 

System view 

Default level 

2: System level 

Parameters 

None 

Description 

Use 

stp bpdu-protection

 to enable the BPDU guard function.  

Use 

undo stp bpdu-protection

 to disable the BPDU guard function.  

By default, the BPDU guard function is disabled.  

Examples 

# Enable the BPDU guard function.  

<Sysname> system-view 

[Sysname] stp bpdu-protection 

stp bridge-diameter 

Syntax 

stp bridge-diameter

 

diameter

 

undo stp

 

bridge-diameter

 

View 

System view 

Default level 

2: System level 

Summary of Contents for WA Series






































































































































Reviews:

No comments