manualshive.com logo in svg

H3C UniServer R4900 G5, Operating System Installation Manual

Share
Download
H3C UniServer R4900 G5 Operating System Installation Manual Download Page 137

 

9 

 

Some NVMe drives might fail to be identified when 
multiple NVMe drives are installed after OS 
installation 

Symptom 

Some NVMe drives might fail to be identified when multiple NVMe  drives are installed after OS 
installation. 

Solution 

To resolve the issue: 

1. 

Install a next NVMe drive a minimum of 20 seconds after one NVMe drive is installed. 

2. 

If the issue persists, contact H3C Support. 

Failed to install CASE0306 on an NVMe SSD 
drive 

Do not install CAS E0306 on an NVMe SSD drive. 

The system cannot be restored after the server is 
powered down unexpectedly 

Symptom 

The system cannot be restored after the server is powered down unexpectedly and the file system is 
damaged. 

Solution 

 

CAUTION: 

Forcibly powering down the server might damage your applications or data. Be cautious to perform 
this operation based on your operating system. 

 

To resolve the issue: 

1. 

Restart the system, select 

rescue mode

 on the GRUB page, execute the 

xfs_repair –L 

/dev/sdx

 command to repair the damaged partition, and then restart the system. 

2. 

If the file system cannot be repaired, re-install the system. 

3. 

If the issue persists, contact H3C Support. 

Summary of Contents for UniServer R4900 G5














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands