manualshive.com logo in svg

H3C UniServer R4900 G5, Operating System Installation Manual

Share
Download
H3C UniServer R4900 G5 Operating System Installation Manual Download Page 132

 

4 

 

1. 

Install a GE-4P-360T-B2-1 network adapter. Most systems integrate network adapter drivers of 
this type. 

2. 

Burn the driver of the mLOM adapter into the image of the system, and then use this image for 
PXE installation. 

3. 

If the issue persists, contact H3C Support. 

Failure to install a VMware OS when only mLOM 
adapters are installed 

Symptom 

A VMware OS failed to be installed when only mLOM adapters are installed. 

Solution 

The server detects whether a network adapter exists before installing a VMware OS. If no network 
adapter is detected, the OS will not be installed. The server uses a new-generation chip for mLOM 
adapters, and the mLOM adapter driver is not integrated into VMware, so the server cannot identify 
the mLOM adapter. 

To resolve the issue: 

1. 

Apply either of the following methods:  

 

Use the OS image integrated with the mLOM adapter driver to install the OS. 

 

Install a PCIe card that the VMware-provided drive can identify, for example, network 
adapter-GE-4P-360T-B2-1, CNA-10GE-2P-560F-B2-1, or network 
adapter-10GE-2P-520F-B2-1. 

2. 

If the issue persists, contact H3C Support. 

HBA-H460-M1 storage controller drive can be 
installed successfully only after two installation 
operations 

Symptom 

The HBA-H460-M1 storage controller drive can be installed successfully only after two installation 
operations. 

Solution 

This issue is caused by smartpqi driver and aacraid driver (provided with the card) conflict. Updating 
smartpqi does not update aacraid. 

•

 

To resolve the issue for a Red Hat OS: 

a. 

Update firmware to version 0.0.B826 or higher. 

b. 

Install smartpqi (v1.02), and then reboot the server. 

c. 

Install aacraid (v52011) to replace aacraid provided with the storage controller. 

d. 

Add 

rdblacklist=aacraid

 to 

/etc/grub2-efi.cfg

, and then reboot the server. 

e. 

Execute the 

lspci -vvs b3:00.0

 command to verify that the drive in use is smartpqi. 

Summary of Contents for UniServer R4900 G5














































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands