background image

 

2-12 

Figure 2-2 

Network diagram for ACFP configuration 

GE3/0/3

GE3/0/2

GE3/0/1

Router

ACFP client

ACFP server

Host A

192.168.1.1/24

Host B

192.168.1.2/24

Host C

192.168.2.1/24

Host D

192.168.2.2/24

 

 

Configuration Procedure 

Configuring Router 

# Enable the ACFP server. 

<Router> system-view 

[Router] acfp server enable 

Configuring the collaboration policy and monitoring rules for the ACFP client through MIB 

# Configure the ACFP client. 

Configure the ACFP client through MIB browser to send information to Router, where the client index is 

1, four working modes are supported, namely, host, pass-through, redirect, and mirror (by setting the 

node h3cAcfpClientMode), and the other parameters adopt the default values. 

# Configure the ACFP policy. 

Configure the ACFP policy through MIB browser to send information to Router, where the client index 

and policy index is 1, the policy inbound interface is GigabitEthernet 3/0/2 (by setting the node 

h3cacfpPolicyInIfIndex), the policy destination interface is GigabitEthernet 3/0/3 (by setting the node 

h3cAcfpPolicyDestIfIndex) and the other parameters adopt the default values. 

# Configure the ACFP rule. 

Configure the ACFP rule through MIB browser to send information to Router, where both the client 

index and policy index is 1, the action is 

redirect 

(by setting the node h3cAcfpRuleAction), and the 

other parameters adopt the default values. 

Configuring the collaboration policy and filtering rules for the ACFP client through MIB 

# Configure the ACFP policy. 

Configure the ACFP policy through MIB browser to send information to Router, where the client index is 

1, policy index is 2, the policy inbound interface is GigabitEthernet 3/0/2 (by setting the node 

h3cAcfpPolicyInIfIndex), and the other parameters adopt the default values. 

# Configure the ACFP rule. 

Apply the ACFP rule through MIB Browser to send information to Router, where the client index is 1, 

policy index is 2, the action is 

permit 

(by setting the node h3cAcfpRuleAction), the packets whose 

source IP address is 192.168.1.1 are matched (by setting the node h3cAcfpRuleSrcMAC), the wildcard 

Summary of Contents for SR6600 SPE-FWM

























Reviews: