61
[Sysname-nqa-admin-test-tcp] reaction 1 checked-element probe-fail threshold-type
consecutive 3 action-type trigger-only
Related commands
track
(
High Availability Command Reference
)
reaction checked-element rtt
Use
reaction checked-element rtt
to configure a reaction entry for monitoring packet
round-trip time.
Use
undo reaction
to delete a reaction entry.
Syntax
reaction
item-number
checked-element rtt threshold-type
{
accumulate
accumulate-occurrences
|
average
}
threshold-value upper-threshold
lower-threshold
[
action-type
{
none
|
trap-only
}
]
undo reaction item-number
Default
No reaction entries for monitoring packet round-trip time exist.
Views
ICMP jitter/UDP jitter/voice operation view
Predefined user roles
network-admin
Parameters
item-number
: Assigns an ID to the reaction entry, in the range of 1 to 10.
threshold-type
: Specifies a threshold type.
accumulate
accumulate-occurrences
: Checks the total number of threshold violations.
Available value ranges include:
•
1 to 15000 for the ICMP jitter and UDP jitter operations.
•
1 to 60000 for the voice operation.
average
: Checks the packet average round-trip time.
threshold-value
: Specifies threshold range in milliseconds.
upper-threshold
: Specifies the upper limit in the range of 0 to 3600000.
lower-threshold
: Specifies the lower limit in the range of 0 to 3600000. It must not be greater
than the upper limit.
action-type
: Specifies what action to be triggered. The default action is
none
.
none
: Specifies the action of displaying results on the terminal display.
trap-only
: Specifies the action of displaying results on the terminal display and meanwhile
sending SNMP trap messages to the NMS.
Usage guidelines
You cannot edit a reaction entry after it is created. To change the attributes in a reaction entry, use
the
undo reaction
command to delete the entry, and then configure a new one.
Only successful probe packets are monitored. Statistics about failed probe packets are not collected.
Summary of Contents for SOHO IE4300
