Installation accessories
安装附件介绍
No installation tools are provided with the device. Prepare them yourself as required.
设备不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。
1
Flat-blade screwdriver
一字螺丝刀
Phillips screwdriver
十字螺丝刀
Needle-nose pliers
尖嘴钳
ESD wrist strap
防静电腕带
Diagonal pliers
斜口钳
BOM: 3104A0WC
Tool list
工具参考
H3C SecPath L5030[L5060][L5080][L5000-E] Load Balancing Device Installation Quick Start-APW101
H3C SecPath L5030[L5060][L5080][L5000-E]
负载均衡设备 快速安装指南
-APW101
Wear an ESD wrist strap, and make sure the wrist strap makes good skin contact and is reliably grounded.
操作者需佩戴防静电腕带，确保防静电腕带与皮肤良好接触，并确认防静电腕带已经良好接地。
Cage nut
浮动螺母
M4 screw
M4
挂耳螺钉
M6 screw
M6
机柜螺钉
Wire-stripping pliers
剥线钳
Wire crimper
压线钳
Mounting brackets with cable
management brackets
带走线架的挂耳
2
Installing a fan tray
安装风扇模块
The FAN-20F-2-A blows air from the power module side to the port side and the fan tray handle is blue. The
FAN-20B-2-A draws air from the port side to the power module side and the fan tray handle is red.
Before installing a fan tray, make sure the fan tray has an airflow direction that draws in cool air from the
cold aisle and exhausts hot air to the hot aisle.
You must install fan trays of the same model on a device.
FAN-20F-2-A
为吹风风扇，风向为电源侧进风，端口侧出风，风扇把手为蓝色；
FAN-20B-2-A
为抽风风扇，
风向为端口侧进风，电源侧出风，风扇把手为红色。
安装风扇模块前，请根据风扇模块的风向指示，确认气流方向和安装环境的通风要求一致。
不支持抽风风扇和吹风风扇混插。
Marker
记号笔
The device comes with the two fan tray slots empty. Before powering on the device, make sure the device
has two fan trays of the same model installed.
If one or both fan trays fail during the device operation, replace the fan trays immediately and keep the fan
trays in position before the replacement.
设备出厂时两个风扇插槽均为空
，
为保证设备的正常散热
，
用户必须安装两个相同型号的风扇模块
，
否则
禁止设备上电运行
。
在设备运行过程中，如果一个或两个风扇模块出现故障，请及时进行更换，且更换故障风扇模块前需保持
故障风扇模块在位。
Grounding cable
地线
Removable cable tie
扎带
Slide rails and chassis rails
滑道及滑道导轨
Correctly orient the fan tray with
the "TOP" mark on top.
请确保“
TOP
”标识朝上
Airflow direction of the device
设备风向设计
The device can provide front-to-rear or rear-to-front airflow by using different fan trays.
设备采用前后风道设计，通过安装不同的风扇模块，提供两种散热方式，满足不同环境下的散热要求。
1
2
1
FAN-20F-2-A fan tray
FAN-20F-2-A
风扇模块
FAN-20B-2-A fan tray
FAN-20B-2-A
风扇模块
The installation procedure is similar for the L5030, L5060, L5080, and L5000-E devices. This guide uses the
L5000-E as an example.
L5030/L5060/L5080/L5000-E
安装方法类似，本手册仅以
L5000-E
为例进行介绍。
Summary of Contents for SecPath L5000-E
Page 4: ......
