manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 347

Command Manual – GRE 
H3C S9500 Series Routing Switches

 

Chapter 1  GRE Configuration Commands

 

1-10

 

1.1.7  interface tunnel 

Syntax 

interface tunnel

 

number

 

undo interface tunnel

 

number

 

View 

System view 

Default Level 

2: System level 

Parameters 

number

: Tunnel interface number, in the format of board slot number/0/Tunnel interface 

number. 

Description 

Use the 

interface tunnel

 command to create a tunnel interface and enter tunnel 

interface view. 

Use the 

undo interface tunnel

 command to remove a tunnel interface. 

By default, there is no tunnel interface on the device. 

z

 

Executing the 

interface tunnel

 command, you enter tunnel interface view if the 

tunnel interface exists. 

z

 

A tunnel interface number has only local significance. Therefore, the same or 

different interface numbers can be set at both ends of a tunnel. 

Related commands: 

source

, 

destination

, 

tunnel-protocol

.  

Examples 

# Create Tunnel 3/0/0. 

<Sysname> system-view 

[Sysname] interface tunnel 3/0/0. 

1.1.8  ipv6 mtu (tunnel Interface view) 

Syntax 

ipv6 mtu

 

mtu-size 

undo ipv6 mtu 

View 

Tunnel interface view 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands