manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 344

Command Manual – GRE 
H3C S9500 Series Routing Switches

 

Chapter 1  GRE Configuration Commands

 

1-7

 

Table 1-3 

Description on the fields of the 

display interface tunnel

 command 

Field 

Description 

Tunnel3/0/0 current state: UP 

Status of the physical layer of the tunnel 
interface is UP 

Line protocol current state: UP 

Status of the link layer of the tunnel 
interface is UP 

Description 

Descriptive information of the tunnel 
interface 

Tunnel3/0/0 Interface 

Number of the tunnel interface 

Maximum Transmit Unit 

Maximum transmission unit of the 
tunnel, 1500 bytes in this example 

Encapsulation is TUNNEL 

The encapsulation protocol is TUNNEL.

aggregation ID 

ID of the service loop group applied to 
the tunnel.  

Tunnel source 

Source address of the tunnel interface 

destination 

Destination address of the tunnel 
interface 

Tunnel protocol/transport 

The Tunnel protocol/transport protocol 
that is in operation 

GRE key 

Keyword verification 

Checksumming of GRE packets 

End-to-end verification 

Last 300 seconds input 

Amount of inbound traffic per second in 
the last five minutes, in bytes and in 
packets respectively 

Last 300 seconds output 

Amount of outbound traffic per second in 
the last five minutes, in bytes and in 
packets respectively 

packets input 

Total number of bytes input 

input error 

Number of inbound packets in error 

packets output 

Total number of bytes output 

output error 

Number of outbound packets in error 

 

1.1.5  display ipv6 interface tunnel 

Syntax 

display ipv6 interface tunnel

 

number

 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands