H3C S9500 Series Command Manual Download Page 341

Page: 341 / 350

Command Manual – GRE
H3C S9500 Series Routing Switches

Chapter 1 GRE Configuration Commands

1-4

<Sysname> debugging gre all

<Sysname> terminal debugging

<Sysname> ping ipv6 -c 1 2001:100::3

PING 2001:100::3 : 56 data bytes, press CTRL_C to break

*Mar 23 14:39:28:359 2007 Sysname GRE/7/debug:Slot=2;

Tunnel2/0/1 packet: Before encapsulation,

Incoming packet header 2001:0100::0001->2001:0100::0003(length = 104)

Reply from 2001:100::3

bytes=56 Sequence=1 hop limit=64 time = 7 ms

*Mar 23 14:39:28:566 2007 Sysname GRE/7/debug:Slot=2;

Tunnel2/0/1 packet:After encapsulation,

Outgoing packet header 10.100.10.1->10.100.20.3(length = 128)

--- 2001:100::3 ping statistics ---

1 packet(s) transmitted

1 packet(s) received

*Mar 23 14:39:28:756 2007 Sysname GRE/7/debug:Slot=2;

Tunnel2/0/1 packet: GRE physical transmit a packet(len = 128), usProtocol =

0x8

6dd.

0.00% packet loss

round-trip min/avg/max = 7/7/7 ms

*Mar 23 14:39:28:926 2007 Sysname GRE/7/debug:Slot=2;

gre packet: Decapsulate tunnel packet

Outer packet header 10.100.20.3->10.100.10.1(length = 128)

*Mar 23 14:39:29:126 2007 Sysname GRE/7/debug:Slot=2;

Tunnel2/0/1 packet: After decapsulation,

Outgoing packet header 2001:0100::0003->2001:0100::0001(length =

104)

1.1.3 destination

Syntax

destination

{

Ip-address

Ipv6-address

}

undo destination

View

Tunnel interface view

Summary of Contents for S9500 Series































































































































































































































































































































































Search results

Summary of Contents for S9500 Series

Reviews:

Brands by name

Popular brands

H3C S9500 Series, Command Manual

Search results

Summary of Contents for S9500 Series

Reviews:

Brands by name

Popular brands