manualshive.com logo in svg

H3C S9500 Series, Command Manual

Share
Download
H3C S9500 Series Command Manual Download Page 329

Command Manual – MPLS L3VPN 
H3C S9500 Series Routing Switches 

Chapter 1  MPLS L3VPN Configuration Commands

 

1-66 

Parameters 

cr-lsp

: Specifies CR-LSP tunnels. 

lsp

: Specifies LSP tunnels. 

number

: Number of tunnels for load balancing, one by default.  

Description 

Use the 

tunnel select-seq

 

load-balance-number

 command to configure the 

preference order for tunnel selection and the number of tunnels for load balancing. 

Use the 

undo tunnel

 

select-seq 

command to restore the default. 

Note that: 

z

 

Only tunnels of the types specified in the 

tunnel select-seq 

load-balance-number

 command can be used.  

z

 

A tunnel type closer to the 

select-seq

 keyword has a higher priority.  

z

 

The number of tunnels for load balancing refers to the number of tunnels that an 

application can use. 

By default, one LSP tunnel can be used. That is, only LSP tunnels can be used and the 

number of tunnels for load balancing is 1. 

Examples 

# Define a tunneling policy, specifying that only CR-LSP tunnels can be used and the 

number of tunnels for load balancing be 2. 

<Sysname> system-view 

[Sysname] tunnel-policy po1 

[Sysname-tunnel-policy-po1] tunnel select-seq cr-lsp load-balance-number 2 

1.1.59  vpn-instance-capability simple 

Syntax 

vpn-instance-capability simple 

undo vpn-instance-capability 

View 

OSPF multi-instance view 

Default Level 

2: System level 

Parameters 

None 

Summary of Contents for S9500 Series































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands