H3C S7500E-XS Series Installation Manual Download Page 50

 

43 

Appendix B FRUs and compatibility matrixes 

Table 8

 

Compatibility matrix between the FRUs and S7500E-XS switches 

FRUs S7502E-XS 

S7504E-XS 

Power modules 

LSVM1AC650 Yes 

Yes 

LSVM1DC650 Yes 

Yes 

Fan trays 

LSQM1HFANSCB Yes 

No 

LSQM1BFANSCB No 

Yes 

Interface cards 

LSQM1QGS8A0 Yes 

Yes 

LSQM1TGT24QSM0 Yes 

Yes 

LSQM1TGS24QSM0 Yes 

Yes 

LSQM1TGS24QSA0 Yes 

Yes 

 

 

IMPORTANT: 

 

The S7502E-XS switches can operate correctly with only one power module. You can install two power
modules on the switches for 1+1 redundancy. 

 

The S7504E-XS switches can operate correctly with two power modules. You can install four power 

modules on the switches for 2+2 redundancy. 

 

You must install two fan trays of the same model for the switch. 

 

Power modules 

 

CAUTION: 

When the switch has power modules in redundancy, you can replace a power module without powering
off the switch. Make sure the power module to be replaced is powered off before you replace it. 

 

Table 9

 

Power module specifications 

Power module 

Specifications 

LSVM1AC650 

 

Rated input voltage:  
100 VAC to 240 VAC @ 50 Hz or 60 Hz 

 

Max input voltage:  
90 VAC to 264 VAC @ 47 Hz to 63 Hz 

 

Max output power:  

650 W 

Summary of Contents for S7500E-XS Series

































































Reviews: