manualshive.com logo in svg

H3C s5820x series, Command Reference Manual

The H3C s5820x series is a cutting-edge networking product designed to meet the demands of modern enterprises. Ensure seamless installation and configuration with the Quick Start Manual, available for free download from manualshive.com. This comprehensive manual provides step-by-step instructions to maximize the performance of your network infrastructure.

Share
Download
background image

 

6-32 

 

ebgp-interface-sensitive 

Syntax 

ebgp-interface-sensitive 

undo ebgp

-

interface-sensitive 

View 

BGP view, BGP-VPN instance view 

Default Level 

2: System level 

Parameters 

None 

Description 

Use the 

ebgp-interface-sensitive

 command to enable the clearing of EBGP session on any interface 

that becomes down. 

Use the 

undo

 

ebgp-interface-sensitive

 command to disable the function. 

 

This function is enabled by default.   

Examples 

# In BGP view, enable the clearing of EBGP session on any interface that becomes down.   

<Sysname> system-view 

[Sysname] bgp 100 

[Sysname-bgp] ebgp-interface-sensitive 

# In BGP-VPN instance view, enable the clearing of EBGP session on any interface that becomes 

down (the VPN has been created). 

<Sysname> system-view 

[Sysname] bgp 100 

[Sysname-bgp] ipv4-family vpn-instance vpn1 

[Sysname-bgp-vpn1] ebgp-interface-sensitive 

filter-policy export (BGP/BGP-VPN instance view) 

Syntax 

filter-policy

  {

 acl-number

 | 

ip-prefix

 

ip-prefix-name

 } 

export

 [ 

direct

 | 

isis

 

process-id

 | 

ospf

 

process-id

 | 

rip

 

process-id

 | 

static 

] 

undo filter-policy

 

export 

[ 

direct

 | 

isis process-id 

|

 ospf process-id 

|

 rip process-id 

|

 static 

] 

View 

BGP view, BGP-VPN instance view 

Default Level 

2: System level 

Parameters 

acl-number

: Number of an ACL used to filter outgoing routing information, ranging from 2000 to 3999.   

Summary of Contents for s5820x series









































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for s5820x series

FAAC T10E Quick Start Manual preview
T10E
Brand: FAAC Pages: 2
H3C S9500E Series Manual preview
S9500E Series
Brand: H3C Pages: 38
H3C S9500E Series Interface Configuration Manual preview
S9500E Series
Brand: H3C Pages: 36
H3C S9500E Series Quick Start Manual preview
S9500E Series
Brand: H3C Pages: 9
H3C S9500E Series Command Reference Manual preview
S9500E Series
Brand: H3C Pages: 36
H3C S12500X-AF Series Configuration Examples preview
S12500X-AF Series
Brand: H3C Pages: 21
H3C S12500X-AF Series Quick Start Manual preview
S12500X-AF Series
Brand: H3C Pages: 42
H3C H3C S7500E-X Configuration Examples preview
H3C S7500E-X
Brand: H3C Pages: 16
H-Tronic TS 1000 Manual preview
TS 1000
Brand: H-Tronic Pages: 32
Balluff IO-Link BNI LH1-303-S11-K091 Installation Manual preview
IO-Link BNI LH1-303-S11-K091
Brand: Balluff Pages: 12
Allied Telesis CentreCOM GS970M Series Quick Installation Manual preview
CentreCOM GS970M Series
Brand: Allied Telesis Pages: 21
Ask HDSW0024M1 User Manual preview
HDSW0024M1
Brand: Ask Pages: 4
Orno OR-GB-422 Quick Start Manual preview
OR-GB-422
Brand: Orno Pages: 2
Manhattan 177290 User Manual preview
177290
Brand: Manhattan Pages: 4
Gefen ToolBox GTB-MHDMI1.3-441 User Manual preview
ToolBox GTB-MHDMI1.3-441
Brand: Gefen Pages: 25
PRO SIGNAL PSG3061 Quick Start Manual preview
PSG3061
Brand: PRO SIGNAL Pages: 4
Scion SC03.4101 Operation Manual preview
SC03.4101
Brand: Scion Pages: 8
Planet WGSW-5240 Specifications preview
WGSW-5240
Brand: Planet Pages: 2

Brands by name

Popular brands

Load more brands