H3C DSIC-9FSW Manual Download Page 128 | Manualshive

Page: 128 / 219

background image

119

Table 163 LED description

LED Description

LINK/ACT

•

On: Carrier signal has been received.

•

Flashing: Data is being received or/and transmitted.

•

Off: No carrier signal has been received.

LP/AL

•

On: The interface is in a loopback.

•

Off: No loopback or alarm is present.

•

Flashing: An alarm indication signal (AIS), loss of frame alignment (LFA) signal,
or remote alarm indication (RAI) signal is present.

LINK/ACT

•

On: Carrier signal has been received.

•

Flashing: Data is being received or/and transmitted.

•

Off: No carrier signal has been received.

LP/AL

•

On: The interface is in a loopback.

•

Off: No loopback or alarm is present.

•

Flashing: An alarm indication signal (AIS), loss of frame alignment (LFA) signal,
or remote alarm indication (RAI) signal is present.

Interface cables and the connection methods

For more information about E1 interface cables and the connection methods, see "

."

FIC-1T1/FIC-2T1/FIC-4T1 and

FIC-1T1-F/FIC-2T1-F/FIC-4T1-F

Introduction

•

FIC-1T1/FIC-2T1/FIC-4T1

The 1-/2-/4-port channelized CT1/PRI interface module (FIC-1T1/FIC-2T1/FIC-4T1) transmits,
receives, and processes T1 data traffic. In addition, you can use the module for other purposes,
such as CT1 access and the ISDN PRI function.

•

FIC-1T1-F/FIC-2T1-F/FIC-4T1-F

The 1-/2-4-port fractional T1 interface module (FIC-1T1-F/FIC-2T1-F/FIC-4T1-F) differs from
the FIC-1T1/FIC-2T1/FIC-4T1 primarily in the sense that:

{

The FT1 operating mode supported by the T1-F modules allows only one n No 64 kbps or n
No 56 kbps bundle to be formed on each interface, where n = 1 to 24. However, a T1 module
allows arbitrary grouping of 24 channels and multiple bundles.

{

The FIC-T1-F modules do not support PRI mode.

«
...
126
127
128
129
130
...
»

Summary of Contents for DSIC-9FSW




























































































































































































































Reviews:

No comments

Related manuals for DSIC-9FSW

Brand: ABB Pages: 370

Brand: ABB Pages: 17

Brand: ABB Pages: 104

Brand: ABB Pages: 120

Brand: ABB Pages: 42

Brand: Bartlett Pages: 30

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

7000-2 - Escalade RAID Controller

Brand: 3Ware Pages: 2

Brand: Danfoss Pages: 85

VLT Decentral FCD 300

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 4

VLT 6000 series

Brand: Danfoss Pages: 27

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 20

ADAP-KOOL AK-PC 781

Brand: Danfoss Pages: 14

Brand: Danfoss Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands