GW Instek LCR-6000 Series User Manual Download Page 26

Page: 26 / 143

Startup

Setup Key

BNC Terminal

Trigger Key

ESC Key

USB Disk Port (USB-Host)

System Soft-key

3.2

Rear Panel

Figure 3-2

Rear Panel

Table 3-2

Rear panel description

No.

Description

Power Cable Receptacle(Outlet) (to LINE)

Frame Terminal

RS-232C Interface

Handler Interface

3.3 Power On/Off

3.3.1 Power On

Press the power key for at least 2 seconds. Release power

key when the POWER LED is lit.

3.3.2 Power Off

Press the power key at least 2 seconds. LCR-6000 Series
will shut down when you release the power key.
If the AUTOSAVE option of the File Operation menu is

set to ON (see page 78), the POWER LED will flash twice

and the AUTOSAVE function will be executed during the
power-off sequence.

Summary of Contents for LCR-6000 Series
















































































































































Search results

Summary of Contents for LCR-6000 Series

Reviews:

Related manuals for LCR-6000 Series

Brands by name

Popular brands

GW Instek LCR-6000 Series, User Manual

Search results

Summary of Contents for LCR-6000 Series

Reviews:

Related manuals for LCR-6000 Series

Brands by name

Popular brands