GW Instek COM-804 User Manual Download Page 71

Page: 71 / 157

GOM-804 & GOM-805 User Manual

Brightness

Background

The Brightness setting sets the backlight brightness of
the TFT-LCD panel.

1. Select
Brightness
setting

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display

has focus.
Go to System and press Enter.
Go to Utility and press Enter.
Go to Brightness and press Enter.

System

menu icon

Move

Select menu

or setting

Enter

2. Brightness
setting appears

Use the arrow keys to set the brightness level. Press
Enter to confirm the setting.

Brightness

01 (dim) ~ 05 (bright)

Note

Pressing ESC before pressing ENTER will exit from the
Brightness settings.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands