GW Instek COM-804 User Manual Download Page 68

Page: 68 / 157

MEASUREMENT

System Settings

Background

The System settings are used to view the system
information, set the power on state, the remote interface,

screen brightness, external interface and beep settings as
well as access the calibration menu.

System Information

Background

The System Information will show the manufacturer,
model, software version and serial number of the unit.

The system information is the equivalent of the return
string from the *idn? query (page 144).

1. View System
Information

From one of the main screens, press
the

ESC

key so that the menu

system at the bottom of the display

has focus.
Go to System and press Enter.
System information will be displayed
at the top of the System menu.

System

menu icon

Move

Select menu

or setting

Enter

System Information

Note

Pressing ESC will exit from the System menu.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for COM-804






























































































































































Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands

GW Instek COM-804, User Manual

Search results

Summary of Contents for COM-804

Reviews:

Related manuals for COM-804

Brands by name

Popular brands