GUDEL FlexxPump4 D Operating Manual Download Page 39

Page: 39 / 151

5.4.3

Connect hydraulics

NOTE

Material damage

Closing hydraulic outputs creates an overpressure. The overpressure can
cause damage to the product.

• Do not close any hydraulic outputs

5.4.3.1

FlexxPump4 D 3-fold

Lubrication system with 3 lubrication points

D003078

Fig. 5-2

Design FlexxPump4 D 3-fold

Lubricating pinion (not included in the
scope of delivery)

Y-segment

Lubricating element (not included in the
scope of delivery)

Lubrication line hose diameter of
6/3 mm

FlexxPump4 D

1. Axis (not included in the scope of de-
livery)

Commissioning

OPERATING MANUAL Lubrication system
FlexxPump4 D

9007202674126091_v2.0_

EN-US

Summary of Contents for FlexxPump4 D
























































































































































Search results

Summary of Contents for FlexxPump4 D

Reviews:

Related manuals for FlexxPump4 D

Brands by name

Popular brands

GUDEL FlexxPump4 D, Operating Manual

Search results

Summary of Contents for FlexxPump4 D

Reviews:

Related manuals for FlexxPump4 D

Brands by name

Popular brands