GUDEL FlexxPump4 D Operating Manual Download Page 110

Page: 110 / 151

9.4.1.1

Cleaning the rails and racks

DANGER

Moving the axis

The work requires moving the axis. This can lead to severe or fatal injuries!

• Ensure that no persons are in the danger area while the axis is moving

CAUTION

Risk of injury

There is a risk of cuts and crushing in the area of the gearbox, pinion, and
racks.

• Wear appropriate protective clothing

Fig. 9-1

Cleaning rails and racks

Cleaning agents

mild universal cleaner free from aromatic compounds (e.g. Motorex OPAL
5000)

Tab. 9-1

Cleaning agents: Rails and racks

Clean the rails and racks as follows:

Switch off the system and secure it with a padlock against being switched
on again

Clean the rails and racks thoroughly

The rails and racks have been cleaned.

Decommissioning, storage

OPERATING MANUAL Lubrication system FlexxPump4 D

9007202674126091_v2.0_

EN-US

110

Summary of Contents for FlexxPump4 D
























































































































































Search results

Summary of Contents for FlexxPump4 D

Reviews:

Related manuals for FlexxPump4 D

Brands by name

Popular brands

GUDEL FlexxPump4 D, Operating Manual

Search results

Summary of Contents for FlexxPump4 D

Reviews:

Related manuals for FlexxPump4 D

Brands by name

Popular brands